What results when you open the circuit and stop current to an inductor? Select one: counter voltage across the open contacts. energy in the magnetic field disappears. voltage is stored in the coil until the circuit is closed again. immediate loss of voltage in the circuit.

What results when you open the circuit and stop current to an inductor? Select one: counter voltage across the open contacts. energy in the magnetic field disappears. voltage is stored in the coil until the circuit is closed again. immediate loss of voltage in the circuit.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

For the figure shown below if the current is moving clockwise around the coil. Which direction does the coil rotate? S O The whole coil moves down. The whole coil moves up. The right side goes down, and the left side goes up. The right side goes up, and the left side goes down.
5- Determine the mathematical expressions for current and voltage of capacitor following the closing of the switch. Draw the voltage and current curve. $1 R2 Hilt Vs 20 V 4KQ w R3 10KQ R1 w L C
Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
Post Test Choose the letter of the correct answer. Write the chosen letter on a separate sheet of paper. 1. It is a smail component that lights up when current flows through it. a. Capacitor 2. It regulates the amount of current flowing in an electronic circuit. a. Capacitor 3. These are devices or components which do not require an external source to their operation. b. Fuse c. LED d. Resistor b IC c. Inductors d. Resistor c. passive devices d. electrical devices a. active devices b. electronic components 4. It is a three-terminal active component that is used mainly in boosting or amplifying electrical signals; both AF and RF ranges. a. Capacitor 5. it is necessary to turn the electrical circuit "on" or "off" a. Fuse 6. Testing tools that are capable of executing tests, reporting outcomes, and comparing results with earlier test runs a. Automated 7. The testing method that starts a soon as code is written and continues in successive stages as code is combined with other units of…
Each terminal of a small polarity-independent incandescent bulb is connected to the positive terminals of two (2) DC voltage sources. The negative terminals of these sources are connected together. The first voltage source can have a range of value from 0-12, incrementable by 1.5 volts every turn of the rotary switch (i.e. 0 V, 1.5 V, 3 V, 4.5 V .... 12 V). The voltage of the second source is unknown. Using a luxmeter, the brightness of the lamp was measured for every increment of voltage of the first source. The following observations were recorded: a. 1.5 V produces a higher brightness than 3 V b. 0 V produces a higher brightness than 1.5 V c. 12 V produces higher brightness than 9 V d. 12 V produces equal brightness as 3 V What is the voltage of the second source? Justify each observation.
Alternating current is __________. Select one: A. AN ALTERNATING FLOW OF ELECTRONS B. ELECTRONS REVERSING THEIR FLOW AT REGULAR INTERVALS C. THE MOST COMMONLY USED CURRENT D. ALL OF THE ABOVE
Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. (a) When the switch is “open” i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where does the magnetic flux go in the bar on the right? iv. Where does the current flow in the resistor?
what is difference between high voltage burn and low voltage burn explosion in details
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
Reluctance in a magnetic circuits corresponds to in an electric circuits. Resistance Current O Voltage Charge
The primary voltage on the transformer in Figure 2–46 (p. 96) is 120 V rms and NP : NS = 15:1. Diode voltage drops are 0.7 V. (a) What should be the value of RL if the average current in RL must be 0.5 A? (d) Is it alright to measure with an oscilloscope both the input and output waveforms at the same time in Figure 2-46? Why or why not?
Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. Clearly explain your answers. A) When the switch is closed i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where is the magnetic flux going in the bar on the right? iv. Towards where the current flows in the resistor?