By using Proteus,write a suitable C program for 8051 microcontroller for the subsystem assigned to you based on the flowchart

Q: How to write a step response code With USART for DC-Motor in a Microcontroller STM32 using C…

A: step response code With USART for DC-Motor in a Microcontroller STM32 using C Language   Input…

Q: Give a single C instructions which will set variable n to a 1 if a Watchdog Timeout Reset has not…

A: Hello student

Q: attachInterrupt(0, Interrupt_Yordami, RISING ); analyze the arduino ide line

A: The analysis is as follows:-

Q: 3) Write a Verilog code for a 5-bit up/down counter. The counter has reset and enable control…

A: Up Down counter is the combination of both the counters in which we can perform up or down counting…

Q: Describe the following hardware blocks in a PIC 16F processor. a. Oscillator start-up timer b.…

A: the hardware blocks in a PIC 16F processor Oscillator start-up timer Power-on reset Watchdog timer…

Q: Write a program that rotates the value of three registers clockwise twice i.e. given these initial…

A: Code: #include <stdio.h> int main(){    int ax=10,bx=20,cx=30,temp,i;    int rotations=2;…

Q: Change this MIPS code to RISC-V Assembly using sll.   Please add comments. Allow running in RARS.

A: MIPS to RISC-v assembly using Shift Right logical. The shift right logical instructions in RISC-v is…

Q: Give an example of three instructions, each one automatically affects one of the following: CX, SP…

A: Given CX,SP, Z are the registers  And these are three different types of registers CX is the general…

Q: he automation of a light is designed by interfacing it with the output port having the address 01H…

A: he automation of a light is designed by interfacing it with the output port having the address…

Q: How to check do error correction for user input with upper and lower bounds? NASM assembly   I'm…

A: NASM assembly which refers to the one to the Netwide Assembler is an assembler and disassembler for…

Q: Write assembly code to get data from ch7 of ADC in PIC16F877A and Display the Results on PORTC and…

A: Assembly code to get data from ch7 of ADC in PIC16F877A and Display the Results on PORTC and PORTD…

Q: o AND INT MAIN Write code that uses interrupt timers that allow one led to light up THEN be…

A: Dear Student, The required code for your question is given below -

Q: What's the best way to connect a Micro SD Card Memory Shield Module, an HC-SR04 ultrasonic sensor,…

A: In this question we have to understand about the ways to connect a Micro SD Card Memory Shield…

Q: 10. Suppose that you initialize the ADC module with a right justification setting and then you…

A: 1) When the result is right justified, then the least significant 8 bits of the result will be in…

Q: Write a program in assembly language for PIC18F458 to generate a square wave on RB4 with a period of…

A: The 8051 has 2 counters.When it is used as counters this serves as event counters.

Q: ntrol word in a fe

A: Introduction:The FPU is a coprocessor that is specifically built to process mathematical operations…

Q: What is the minimum size of a register named 'counter' if you need to set it to 50,000,000 count?…

A: The minimum size of a register named 'counter' to set it to 50,000,000 count depends on the maximum…

Q: eed help with a python code that has 2 LEDs connected to one switch or button. When the switch is…

A: It is defined as a interpreted, object-oriented, high-level programming language with dynamic…

Q: How is an external hardware interrupt handled on the INTR pin of the 8086/88?

A: Given: How is an external hardware interrupt handled on the INTR pin of the 8086/88?

Q: Find out the contents of the flag register. Write an APL program to divide AX = 1F55 by CL=1E. The…

A: As we know that DIV operation divides the value present in AX by the operand passed to it and stores…

Q: Using instruction IN AL, DX to read a byte information from an input port, which register must be…

A: We are given an instruction IN AL,DX and we are asked which register must be used to hold the port…

Q: Write down a register transfer statement of 'contents of R1 minus R2 transferred to R3' for a system…

A: Please refer to the following step for the complete solution to the problem above.

Q: Registers in RISC-V are 64-bit.  For the sake of simplicity, consider the following instructions…

A: RISC-V which is an open standard instruction set architecture that are based on established RISC…

Q: Write two unique ARM code segment methods (parts a and b) that will provide the one's compliment of…

A: Here we have given solution for the given task. You can find the solution in step 2.

Q: The register addressing mode was the only one that could be used with a datapath. Which part of the…

A: Introduction: In computer architecture, the datapath is a fundamental component that processes data…

Q: Write a C statement that reload Timer 0 for 1 KHz interrupt frequency.

A: For each timer interrupt, the programme calls a function (which I wrote). And the setvect and…

Q: The purpose of this lab is to control and program the MC8051 Counters of the micro-controller in a…

A: Assembly code is a low level programming language which is between high level language and machine…

Q: What is the Register Transfer Notation of the instruction STR R5, R4, #-28

A: According to the information given:- We have to define the  instruction given  STR R5, R4, #-28

Q: ogram using Timer 0 to create a 10 kHz square wa

A: Below the Assembly Program using Timer 0 to create a 10 kHz square wave on P1.0?

Q: The interrupt service procedure refers to what exactly. In the last instructions for the ISR, RET…

A: Here is the solution:

Q: Write a C-language program Every 4th time through the interrupt (i.e. once every second of time)…

A: #include <REG8252.H>void wait (void)  {                    ;      // for waiting of light…

Q: BCD counter that counts about every 1 second. First write a routine to generate binary outputs:…

A: C++ is an object-oriented programming language, it is used to develop web-browser applications and…

Q: Design an embedded C program to interface a 2x2 keypad and LCD displays with an ARM cortex M3 based…

A: LCD UNIT Let us look at a pin diagram of a commercially available LCD like JHD162 which uses a…

Q: Answer the given question with a proper explanation and step-by-step solution. Qns: In python code…

A: here is an example Python code using the GPIO pins of Raspberry Pi and Motoron M3H256 Triple Motor…

Q: The interrupt service procedure refers to what exactly. In the last instructions for the ISR, RET…

A: Interrupt service routine (ISR): An interrupt service routine (ISR) is a software function that is…

Q: display the voltage at PC0 using the serial terminal every time a push button connected at PB0 is…

A: The answer is

Q: Demonstrate in CXprogrammer with CPH1 device type the SCL3 command using BCD inputs of 3-15 and…

A: Given that Demonstrate in CXprogrammer with CPH1 device type the SCL3 command using BCD inputs of…

Q: I need help programming servo motor to move left and right using discovery board (STM32f407vg)…

A: Answer is given below-