Answer the given question with a proper explanation and step-by-step solution. Qns: In python code write code using GPIO pins from the Raspberry Pi and a Motoron M3H256 Triple Motor Controller for Raspbery Pi. It is using three 12 DC brush motors and we want to control the speed individually, be able to stop motors individually and go counterclockwise as well. please label which motor is being used with one to three and the gpio and the code with details explaining each block.

Answer the given question with a proper explanation and step-by-step solution. Qns: In python code write code using GPIO pins from the Raspberry Pi and a Motoron M3H256 Triple Motor Controller for Raspbery Pi. It is using three 12 DC brush motors and we want to control the speed individually, be able to stop motors individually and go counterclockwise as well. please label which motor is being used with one to three and the gpio and the code with details explaining each block.

CompTIA Linux+ Guide to Linux Certification (MindTap Course List)

4th Edition

ISBN:9781305107168

Author:Jason Eckert

Publisher:Jason Eckert

Chapter6: Linux Server Deployment

Section: Chapter Questions

Problem 18RQ

See similar textbooks

Similar questions

Using the sim8085 write the following code: In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single reading
The ATmega32 is used to flash two separate LEDS. as follows: LED D1 will flash on a frequency 20 kHz and duty cycle of 70%. LED D2 will flash on a frequency of 10 kHz and duty cycle of 35%. Develop a C-code to program this ATmega. 22 23 24 25 26 27 28 29 RESET PCO/SCL PC1/SDA PC2/TCK D2 13 12 XTAL1 XTAL2 PC3/TMS PC4/TDO PC5/TDI 40 39 38 37 36 35 34 33 LED PAO/ADCO PA1/ADC1 PA2/ADC2 PA3/ADC3 PAAIADC4 D1 PC6/TOSC1 PC7/TOSC2 14 15 16 17 18 19 20 21 PDO/RXD LED PAS/ADC5 PAGIADC6 PATIADC7 PD1/TXD PD2/INTO PD3/INT1 PD4/OC1B PD5/OC1A PD6ICP1 PD7/OC2 PBOTOXCK PB1/T1 PB2/AINOINT2 4. PB3/AIN1/OCO PB4/SS PB5/MOSI 7. PB6/MISO AREF AVCC 32 30 PB7/SCK ATMEGA32
given the inputs, please create a circuit that connects to the interface box
Please written by computer source
Please type so that i may be able to read your solution
5- Write a C code that generates a 100 cycles only of waveform at variable frequency where the output frequency is given by: foutput = 5 + n Hz, where n is the Cycle Number n= 0,1, 2..... .99. The output is available from RB10. Given that Fcy = 50 MHz.
As a programmer, you need to design a forward-reverse motor system. When a switch 1 is pressed, the motor will run forward and when a switch 2 is pressed, the motor will run reverse. Use PORT A as input and PORT B as output in PIC16F/18F. Build a suitable program that will fulfill the requirement.
-Design a traffic light controller in which the traffic on an intersection crossing is controlled by a digital circuit using JK Flip-Flops in a synchronous counter. Use traffic signals with red, green and yellow lights on each side of crossing. The lights operate such that red will be on 30 sec. At, the same time, the green light of an adjacent road lights 25 sec followed by the yellow light will be on 5 sec momentarily before the red light goes off. There is a ready timer creating clock pulse of 5 sec per cycle. Design the system by doing the following steps:a) Using block diagram show the plan of circuit and mention the number of JK Flip-Flops that you need.b) Write the truth table of the synchronous counter you need for this design.c) Make the required K-maps and write the Boolean algebraic functions for each J and K inputs using the K-Maps.d) Draw the circuit for this traffic light controller.
a)Write a complete program for the PIC16F84A, with circuit connection as shown in Figure 1(a),so that it flashes the LEDs connected to Port B continuously, in the following patterns:00000000, 00000001, 00000010, 00000100, 00001000, 00010000, 00100000, 01000000,10000000 one after the other with a delay of 1 s inserted between each change of pattern. Use alook-up table to run through the patterns. [Notes: Assume 1s delay subroutine is given. You do not need to write the 1 s delay subroutine] (b) Write a complete program for the PIC16F84A to store even numbers starting from zero inmemory locations 10H to 4FH. For example, 10H should contain 0H, 11H should contain 02H,12H should contain 04H and so on.
Using tinkercad, please may you create a piece of code in Arduino (C/C++) which is going to connect all of these components in the block diagram
Handwriiten answer plzz
Here's a table showing the tco and tro for each of the components in the circuit bellow. Please compute tco and tpo for the whole circuit? tco tPD B Inverter 0.1 ns 0.6 ns AND2 0.4 ns 0.8 ns C XOR2 0.5 ns 1.8 ns MUX2 0.5 ns 1.5 ns