Answer Correctly .Don't Waste my time with Wrong Solution. In a constant volume gas thermometer the following pairs of pressurereadings were taken at the boiling point of water and the boiling pointof sulphur, respectively:Water b.p.Sulphur b.p.50.010020030096.4193387582The numbers are the gas pressures, mm Hg, each pair being taken withthe same amount of gas in the thermometer, but the successive pairsbeing taken with different amounts of gas in the thermometer. Plot theratio of Sb.p.:H2Ob.p. against the reading at the water boiling point, andextrapolate the plot to zero pressure at the water hoiling point. Thisgives the ratio of Sb.p. : H2Ob.p. On a gas thermometer operating at zerogas pressure, i.e., an ideal gas thermometer. What is the boiling point ofsulphur on the gas scale, from your plot?

Answered: boiling point

Engineering

Mechanical Engineering

boiling point

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answer very quickly
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
A Brinell test is performed on a steel using a 1.2 in. diameter indenter with a load of 71825 Ibs. A 0.75 in. Determine in indentation was measured on the surface of the steel. Determine: a) HBN (psi); b) tensile strength (psi) a) HBN = psi b) Tensile strength = psi
The question and data are in pictures. Please answer properly with each steps and explanation. Best of luck. Thank you so much in advance.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
Interface .. must always reflect force equilibrium and provide for a consistent flow of energy, material, and information. is the surface forming a common boundary between two adjacent objects. arises because of the connection between two objects. is one that can move only in its intended direction. Design catalogs are collections of known and proven solutions to design problems. They contain a variety of information useful to design, EXCEPT: physical principles to achieve a function properties of materials solutions of particular machine design problems prototypes
Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
In the last few steps, where did 0.4 come from?
help num3 please,badly need ittt
Stuck need help! Problem is attached. please view attachment before answering. Really struggling with this concept. Please show all work so I can better understand ! Thank you so much.