Block 3 slides along link 2. Q₂A = 35 mm, Q₂F = 16.25 mm, Q,C= 27.5 mm, Q,G = 15.625 mm, GB = 30 mm, FB = 20 mm, Q₂Q. = 27.5 mm. If the velocity vector of A is 20 mm long, find the velocity vector of B by centro method. Indicate the scale you used. wwwwww F 8 6 2 60 B A d G

Q: Compute the coordinates of the centroid (7,5) of the area shown. Also compute the area moment of…

A: Given: a=14 mm b =113 mm c=18 mm d =49 mm h=99 mm w=14 mm Required: x and y coordinate of centroid…

Q: Determine the component Ux, Uy, and Uz of the vector with a magnitude of 1175 units. Using the…

A: Given: The magnitude of U is 1175 units. Consider the figure,

Q: 4.2 Suppose that P=91lbs. What will the force Q be in this case

A: Therefore, The Force Q when P= 91 lbs will be 1638 lbs.

Q: : Prove that (1) Ya = Gs Yw 1+e

A:

Q: SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool.…

A:

Q: 5. Which of the following steps is/are INCORRECT when getting the resultant of multiple concurrent…

A: S2 is wrong ,As the resultant is not obtained by simply adding the components but by taking the…

Q: I need detailed help solving (c), please.

A:

Q: Question 5. For the triangle shown, determine the third side c and the and if b = 8 ft, h = 6 ft. 8…

A: GUVEN- A right angle triangle where  b =8 ft and h= 6ft…

Q: A Surveyor's steel tape 30 m long has a cross-section of 15 mm x 0.75 mm. With this, line AB is…

A: Length of tape L=30 m, Area A=15 mm x 0.75 mm, Force P=120 N, Modulus of elasticity E=200 kN/mm2. To…

Q: Flow and spacing are inversely related O True O False

A: State true or false Flow and spacing are inversely related

Q: Solve and determine INAX , INAY, and Area total. Show complete solution.

A:

Q: 3. The following details refer to the bar shown in figure. Portion Length Cross section АВ 600 mm 40…

A: Given: The length of AB is 600 mm. The length of BC is 800 mm. The length of CD is 1000 mm. The…

Q: • 1. a. How far does a particle travel between zero to four seconds if its position is given by: S…

A: Calculate the distance travelled by the particle at t=0 by substituting t=0 in the given distance…

Q: Plss write the whole solution or answer om the paper ang draw the figure. And show to get the…

A:

Q: Please refer to the attached drawing. For the given case, do the following: a. At points 1 and 2…

A: a) The labelled figure is shown below:

Q: Locate the centroid y of the area. y y = a sin ат.

A: To find:- centroid of given figure

Q: Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional…

A: The cross-sectional area is 600 mm2.The modulus of elasticity is 200 GPa.Consider the figure.

Q: There are two questions to answer. The first question is a truss problem and the second is a frame…

A: Question 1. TrussCut at Section a-a. Assume all forces are in tension. Question 2. Framea. Draw the…

Q: Homework: Determine the displacement and slope of point (C) of the beam shown below. Take E 200 GPa,…

A: Given: A simply supported beam  Required: Deflection and slope at point C using unit load method.

Q: For the given cross-section with the z-axis going across the width and the y axis being the vertical…

A: Given  w = 125 mm Dimensions of cross section   To find Lz (centroidal)

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.