BH 5 BH 4 BH 2 BH 3 Ground surface BH 1 Ground surface Granite rock 30 m 15 m Sand Horizontal tunnel Clay 18 m Granite rock Granite rock NOT TO SCALE Figure 1: Longitudinal cross-section of a site for proposed construction of water transfer tunnel

Q: 4. Estimate the wetted area of a triangular channel having a depth of 5m and the side slope is…

A: To find : Wetted area.

Q: 7. Estimate the top width of a triangular channel having a side slope of 1H:2V and depth of 5m. a)…

A: To find : Top width.

Q: valuate the FoS for the below slope, when it is underlain by a hard stratum as shown below: 1:2.5 H=…

A: To find FOS

Q: Classify the channel bed slopes. Write the methods of calculating length of GVF profile and explain…

A: Flow profiles are classified by the slope of the channel S0, critical slope Sc, normal depth of the…

Q: need the answer as soon as possible

A:

Q: A trapezoidal channel has a top width of 75 feet and a side slope of 1.5:1 (H:V). Using the given…

A: Given Data: The top width of the channel is B=75 ft. The side slope of channel is 1.5:1. The…

Q: Given data : Wetted area3D20.25 m2 Wetted perimeter%3D13.5 m Find hydraulic radius

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: Determine the bed slope of a trapezoidal channel has depth of flow is 1.2m and velocity of flow is…

A: Depth of the flow = y = 1.2m   Velocity of the flow = v = .35m/sec   Manning's coefficient = n =…

Q: A hydraulic jump occurs in a rectangular channel having a discharge of 3.45 m^3/s of water per meter…

A: as per guidelines provided to us we are restricted to solve only 1 question if multiple question are…

Q: A) What is the over Consolidated Ratio (OCR) at the midpoint of the clay layer? B) What is the total…

A: Given:Required:Over consolidation ratio Total horizontal stress at midpoint of clay layer

Q: Determine the slope of a channel if it has a bottom width of 20 ft, a side slope of 2:1, water depth…

A:

Q: A dam cross-section is a square facing a water depth of D=15m. Assuming a 1m strip for analysis and…

A: Given data,  FOS for overturning = 2 D = 15 m Coefficient of friction = 0.5  To find out the…

Q: discharge = 10.8 m^3/sec average velocity = 0.65 meters/sec side slope = 2H : 1V bottom width =…

A:

Q: Use the sketch and channel properties to complete Table 1 below.

A: Longitudinal slope S = 0.001Manning's n = 0.025When depth is 3 ftFlow area = 90 ft2 Wetted perimeter…

Q: 2. A 1.50 m diameter circular channel flowing at maximum velocity is to be replaced by a trapezoidal…

A: Given a circular channel,D=1.50m To be replace by Trapezoidal channel, n=0.030,S=0.01 Find…

Q: Water Resources Engineering: You are given the following information for a triangular channel: Top…

A: Given data: Top width of the channel (B) = 3 m Flow (Q) = 7.23 m3/s (manning’s constant) n = 0.016

Q: Compute the "b" and "d" of a trapezoidal channel if it is most efficient to convey a 6.35 cu.m./s of…

A: Data is as given

Q: A community plan to construct a concrete rectangular channel to pass 10 m³/sec on a slope of 0.003…

A: This question is from Open Channel Flow.

Q: 10 kPa B 0.4 m |+0.5 m++0.5 m++0.5 m+0.5 m- Soil A 1 m Exit Datum 0.75 m 0.5 m FIGURE P6.2

A:

Q: 4. Estimate the wetted area of a triangular channel having a depth of 5m and the side slope is…

A: We have to determine the value of wetted area of the given triangular channel section having depth…

Q: Evaluate the FoS for the below slope, when it is underlain by a hard stratum as shown below: 1:2 H-8…

A:

Q: Example(): Given below a part of project. Calculate the water level at the head of the distributary…

A: The head loss in each watercourse is .The minimum allowable slope is .The length of each course is…

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.