Below is the schematic design of cable bridges. If the force acting on the cable T1 = 100KN, calculate the forces for other cables of C1, C2, C3, C4, TO. All nodes are hinges. T4 30° T3 20° T2 T1=100kN то 10° C4 C3 C2 C1

Below is the schematic design of cable bridges. If the force acting on the cable T1 = 100KN, calculate the forces for other cables of C1, C2, C3, C4, TO. All nodes are hinges. T4 30° T3 20° T2 T1=100kN то 10° C4 C3 C2 C1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beam AB has a negligible mass and thickness and is subjected to a force of 200 N. It is…

Q: 2) The truss is carrying two masses m (mg=100 N). It is supported by a rope at A and pin support at…

Q: Name SURNAME: Student ID: QUESTION 9 The AE cable carrying the concentrated loads is attached to the…

A: a = 2m b = 8m c = 4m d = 6m Load P = 20 kN We have to find out the followings: Drawing…

Q: Thebent rod is supported by a ball-and-socket joint at O, a cable at B, and a slider bearing at D.…

A: Calculating different vectors and their directions:

Q: Find forces in member BF, DG, and cable DH

A: To find force in member BF, DG,DH

Q: The cable segments support the loading shown. Determine: a. the force in AB b. tension force at DC…

Q: Refer from the figure shown below: a.) What force F must be applied to the following static…

Q: Q1) The frame shown below supports 10Olb weight. The cable is attached at A and passes over a smooth…

A: Answer 1) Solution

Q: A chain makes angles Y° and Z° at its supports as shown. Determine the following: (a) sag at point C…

A: Given:- Y= 18.5° Z= 40° X= 14m W= 0.40 Kg/m To find:- a)sag of point C b)tension of support A…

Q: A T 10 ft -25 ft- B Wo 15 ft

Q: 3) A parabolic cable is shown in the figure 3-a) Find xA and xB . 3-b) Determine the minimum…

A: L = 60 mEB=8 mTo find:a) Find xA and xB. b) Determine the minimum tension in the cable.c) Find the…

Q: 1 2 45° A I35° 3 4 2 В W

Q: Rod AB is secured with a cable at point B and a smooth, up and down movable collar from point A.…

Q: 4. The block weighs 3500 kg. Find force in members AB, AC and AD. 1-5m 4m am

A: Given information: Mass of the block = 3500 Kg Weight of the block = m g…

Q: 3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports…

A: Consider the following free body diagram:

Q: Problem 1: The beam ABC, built into the wall at A and supported by a % inch diameter cable at C,…

Q: 4) The cable shown in the figure is subjected to the forces P, and Q. 4-a) Determine the support…

A: step 1-

Q: Problem 4 Express the components of Tension at cable if carry a force of MN Newton? Y

A: It is given that magnitude of the force in the cable is MN Newton=54 N.

Q: 6 KN 53 3m * 5m Find the tension on the cable Find the reaction at c Find the stress in the cable of…

Q: 2.123 A container of weight Wis suspended from ring A. Cable BAC passes through the ring and is…

A: Given: W = 270 lb The tension is the same in both portions of cable BAC. Solution: Free body…

Q: The cable carrying three 400-lb loads has a sag at ate the force in each segment of the cable. - 8…

A: Draw free body diagram Consider the summation of forces in the horizontal direction Ax=Ex…

Q: Pr: Determine al forces acting on body A for tue System shown in Figureců). Body A weighs (200N and…

A: its a problem of mechanics simply analysing forces on a body given surface is smooth so no friction…

Q: Express the components of tension at cable if carry a force 79 Newton

A: Given data, Carry force = 79 N Determine the component of tension at cable?

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

Q: V' B D. H F G W W Z' 6 @ X' = Y' Z'

A: Solution:- Support reaction at A and E Taking moment about C from left end and right end…

Q: Problem 4) Assume the loads applied to the beam result in a uniformly horizontally distributed load…

A: A loaded beam is given in the as shown and it has been asked to determine intensity of uniformly…

Q: D (0,6, 0) m (12, 4, 2) m C B (6, 0, 0) m ーメ (0, 4, 6) m

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

A: 50

Q: For the beam and loading shown, determine the tension in the cable at D and the support reactions at…

Q: point in a catenary cable varies with the y-coordinate of the point as T(y)= To + woy. A uniform…

A: Tension force at B, TB = 500 N Weight w0 = 15 N/m ya= 4 m yB = 8 m

Q: Don't use chat gpt Chatgpt means downvote

Q: 2. The Cable BC carries a tension force of 500 kN. Find the components of the tension force along BA…

A: The given figure is shown below:

Q: The sign has a mass of 100kg with center of mass at G . A pole is supported by ball- and -socket…

Q: The wall crane supports a load of 700 lb. determine the horizontal and vertical components of the…

Q: F1=100N Let F₁ = [F1] N and let F₂ = 350 N. g) Determine the magnitude FA of the force at pin A. h)…

A: Given:F2=350 NSupport A is a hinge support.Therefore, there will be two support reactions( 1…

Q: A 100N load is supported by a strong bar. The tension in the cable is 200N. The value of the axial…

Q: A steel cable and a titanium cable support a rigid bar at A and B. Both cables have cross- sectional…

A: Given :

Q: Problem 3 What are the value of Tension AC and AD if If the Tension of Cable AB is FN Newton to make…

A: Consider the Top view of the figure;

Q: The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes…

A: Given: Ball and socket joint at A and C Point coordinate: A, (0,0,600) B, (600,0,600) C, (800,0,0)…

Q: Q.3) The L-frame in figure below supports forces from two cables. Cable "EAD" passes through a…

A: Given: Force in cable EAD = 800lb and in OCG = 400lb Required Moment about point B, A and O.

Q: A 100N load is supported vt a strong bar as shown in the figure. The tension in the cable is 200 N.…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Below is the schematic design of cable bridges. If the force acting on the cable T1 = 100kN,
calculate the forces for other cables of C1, C2, C3, C4, TO. All nodes are hinges.
T4
30°
T3
20°
T2
T1=100kN
TO
10°
C4
C3
C2
C1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Solution

VIEW

Step 3 Result

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. For the beam and loading shown, determine the tension in the cable and the support reactions at hinge A. Neglect the thickness of the beam and the size and friction of the pulley at E. E 2 kipsft 3 ft 3 ft 2 ft 10 kips 5. Find the maximum weight of the bucket that the wire system can support so that no single wire develops a tension more than 500 N. 3/3 25° 1300 300
The frame ABCD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the tension in the cable is 450 N, determine the moments about the diagonal AD of the force exerted on the frame by portion BH and portion BG of the cable.
Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of weight W = 1000 lb, resting at the hinge D and supported by a cable EF as shown. The cable EF is parallel to AC. D 21 W 5 30² 3 10²-10--10²-107
The cable supports the loading shown. Determine the distance xe the force at point B acts from A. Set P = 40 lb. 5 ft 8 ft 2 ft 30 lb B
Please solve it in neat handwriting. Thank you in advance
Please asap
This subject is Static of Rigid Bodies. Show your solution.
MN=55
Q3: A telephone cable is clamped at A to the pole AB. Knowing that the tension in the left-hand portion of the cable is T1 = 800 lb, determine by trigonometry (a) the required tension T2 in the righthand portion if the resultant R of the forces exerted by the cable at A is to be vertical, (b) the corresponding magnitude of R. 25° T₂
The hinge at A and cable BDC support beam ABC. Cable BDC passes over the pulley D that is pinned to the ceiling. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers.) Determine the tension in the cable in newtons - ? Determine magnitude and direction - magnitude in newtons Ax- ? Ay- ?
Q.1 The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin 3x at A is 20mm and Diameter of cable BD is 30mm. D P 15 (kN) x-2.7(m) 4х 4x Calculate the followings a) Support reactions at A and the axial force in Cable BD. b) Find the axial stress in cable BD and shear stress at pin A in the case of Double shear at A. c) Calculate the deformation and final length of BD if the modulus of elasticity E=200GPA d) Calculate the change in diameter of BD if the Poisson ratio v-0.3. |
The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the tension in the cable is 625.00 N, determine the moment about the diagonal AD of the force exerted on the frame by portion BG of the cable. y 0.925 m 0.35 m G 0.5 m B 0.875 m 0.5 m P H D 0.75 m 0.75 m The moment about the diagonal AD of the force exerted on the frame by portion BG of the cable is N.m.