being pumped into a pool whose cross section is 10 ft x 13 ft while water is discharged through a 2-in-diameter orifice at a constant average velocity of 16 ft/sec. If the water level in the pool rises at a rate of 0.6 in./min, determine (a) the rate of increase in volume (ft3 /min) of water in pool and (b) the rate at which water is supplied to the pool, in gp

being pumped into a pool whose cross section is 10 ft x 13 ft while water is discharged through a 2-in-diameter orifice at a constant average velocity of 16 ft/sec. If the water level in the pool rises at a rate of 0.6 in./min, determine (a) the rate of increase in volume (ft3 /min) of water in pool and (b) the rate at which water is supplied to the pool, in gp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q4: A volume of water equal to 3.5x10" m'is was required to iigate a farm every 10 days. Find a discharge in m'/s if water is applied according to: 1) one day every 10 days, 2) three days every 10 days, 3) five days every 10 days, 4) 12 hrs between day and another, and 5) continuously.
Water enters the lock of a ship canal through 200 ports, each port having a 2 ft x 2 ft cross-section. The lock is 900 ft long and 85 ft wide. The lock is designed so that the water surface in it will rise at a maximum rate of 5 ft/min. For this condition, (a) what is the rate of flow (ft/s) (b) What will be the mean velocity (ft/s) in each port? 85 m 900 m Port Water entering the canal
Compute for the unknown Line AB BC CD DE EA LINE AB BC CD DE EA Distance 300 400 250 350 277.96 DISTANCE 250 UNKNOWN 300 UNKNOWN 400 Bearing S 37 30 E S 43 15 W N 73 W UNKNOWN UNKNOWN BEARING N 73 00 W N 12 45 E S 37 30 E N 65 45 E S 43 15 W ■
Water entering through 5 ft long and 1 inch diameter pipe has a flow rate of 100 kg/min at a temperature of 100°C and pressure of 2 bar. The density of water at these conditions is 961.5 kg/m3. Calculate the rate of work done at the entrance of pipe.
(c) Liquid flows through an orifice in the bottom of a cylindrical tank at a velocity of 4m/s. If the jet diameter is 2.5cm, what is the rate of flow in lit/sec? If the tank is 25cm in diameter, at what rate is the liquid surface falling?
Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two 3/4-pipes. Find the flow rate in the two 3/4-inch pipes.
AFTER JUMP BEFORE Jump dz di theta 50 deg %3D d1 = 1.2 m d2 = 2.5 m w = 4 m %3D For the figure shown, determine the following: a) Rate of Flow: [ Select ] * m3/s b) Specific Energy before the jump: [ Select ] c) Specific Energy after the jump: [ Select ] m d) Power Loss: [Select ] + kW
Assuming the flow into the tank is maintaining the water surface elevation at a constant location, what is the flowrate (L/s) coming out of point 2? (1) D 0.20 m h 0.20 m (2) (3) d 0.01 m (b)
Correct answer only
QUESTION 5 Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m³/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7
Q3: The flow rate in a pipe is 2 m/s. What is the velocity of the flow if the diameter of the pipe is 500 mm? a. 10.186 m/s b. 8.149 m/s c. 6.621 m/s d. 4.584 m/s c. 7.637 m²/s