Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m3/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7

Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m3/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Asapp
Water is pumped through a 600 mm diameter circular pipe which is 1800 meters long at the velocity of three meters per second. Determine the head loss using the Manning’s formula if n = 0.013. What is the discharge amount of water?
Problem 2: Fluid flows through a 20-mm diameter pipe, 150 m long at a Reynolds number of 1,750. Calculate the discharge if the head lost is 175 m.
Estimate the velocity and head loss per 1000 feet given a flow of 4 ft^3/s, pipe diameter of 12" and C factor of 100?.
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 me- ters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? PLEASE INCLUDE FIGURE AND DERIVATION
Q4: A volume of water equal to 3.5x10" m'is was required to iigate a farm every 10 days. Find a discharge in m'/s if water is applied according to: 1) one day every 10 days, 2) three days every 10 days, 3) five days every 10 days, 4) 12 hrs between day and another, and 5) continuously.
Water enters the lock of a ship canal through 200 ports, each port having a 2 ft x 2 ft cross-section. The lock is 900 ft long and 85 ft wide. The lock is designed so that the water surface in it will rise at a maximum rate of 5 ft/min. For this condition, (a) what is the rate of flow (ft/s) (b) What will be the mean velocity (ft/s) in each port? 85 m 900 m Port Water entering the canal
Water is pumped through a 350 mm diameter circular pipe which is 850 meters long at the velocity of 2.5 meters per second. Determine the head loss using the Hazen-Williams formula if C = 110. What is the discharge amount of water?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 300 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump?(PLEASE INCLUDE DRAWING) USE BERNOULLI'S ENERGY EQUATION
q5 (b) The discharge and velocity of flow over the model of a spillway are 4 m3/s and 3.2 m/s, respectively. Determine the velocity and discharge over the prototype, which is 25 times the size of the model. Refer to Table 5(b).
Q3: The flow rate in a pipe is 2 m/s. What is the velocity of the flow if the diameter of the pipe is 500 mm? a. 10.186 m/s b. 8.149 m/s c. 6.621 m/s d. 4.584 m/s c. 7.637 m²/s
3. **A 32800 ft long pipeline, of commercial steel with the nominal diameter of 12 inch of schedule number 40, conveys water from a reservoir (top water level 2790 ft above the sea level) to a water treatment plant (2230 ft above the sea level). Assuming that the reservoir remains full, and neglecting minor losses, estimate the volume flow rate. Take the viscosity µ = 1.00 CP.