Beam PORS as in Figure Q1 is pin connected at P and S. (a) Develop the shear force (V) and bending moment (M) as function of x for section RS, taking point P as the origin. (b) Draw the shear force and free body diagrams of the entire beam and indicate all important points on the diagrams. [Note: All calculations must be clearly shown] 40 kN 10 kN/m ols S 20 kN.m 4 m 2 m 4 т Figure Q1

Beam PORS as in Figure Q1 is pin connected at P and S. (a) Develop the shear force (V) and bending moment (M) as function of x for section RS, taking point P as the origin. (b) Draw the shear force and free body diagrams of the entire beam and indicate all important points on the diagrams. [Note: All calculations must be clearly shown] 40 kN 10 kN/m ols S 20 kN.m 4 m 2 m 4 т Figure Q1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An extruded beam has the cross section shown. Determine the location e of the shear center O. 5 mm C B 4 mm 0 Z P Answer: e D 4 mm 5 mm 45 mm F 30 mm 70 mm 30 mm mm
es A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, F Ra 1 X Y 12 Determine the section modulus of the beam. Select the correct response: 72113.831 mm³ 87833.695 mm³ 57962.384 mm3 45378.561 mm³ Ri 12
365 For a 200 mm x 200 mm beam shown below with E = 20 GPa, select in the choices %3D the value that most nearly gives the following; Use Conjugate Beam Method 25.50 Reaction at D in kN [ Select ] Deflection at B in mm [ Select ] Deflection at C in mm 19 kN/m 5 kN/m BI 4.2 m 3 m - -3.6 m B & C are int. hinge %23 to search acer
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
Q6 Derive the slope and elastic curve equation for the beam shown in Figure 6. Mo B D A C Figure 6
Solve the problem with complete and neat solution. Draw the figure. 1. Compute the support reactions of the beam shown. Support at A is a roller and at B is a hinge. IN 1IN 100N /m 30N/m 52N/m 1m 3m 5m 7m
A beam assembly shown below is supported by a simple hinge and roller supports at A and C respectively. The 8-ft-long segment A-C (a = 4 ft) has a uniform cross section as shown in the figure, right (cross section at e-e). The beam assembly is subjected to a concentrated load (P = 3 kip) at point D, which is directly above point A. Take E = 31500 ksi. D e e R Cross section at e---e 46 3b b Ab 4b Figure 4: Simply supported beam with point load and cross-section If the maximum tensile and compressive bending stresses in the segment A-C cannot exceed ±100 ksi without failure, respectively, determine the smallest allowable dimension b in the segment cross section (see cross section at e-e above, which applies to the whole segment AC). Use F.S. = 2.
For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa. D 0.9 m ACD 500 mm² 0.6 m 25 kN AAB 850 mm² 1.5 m E 0.3 m² 0.2mAF
Solve the problem with complete and neat solution. Draw the figure. 1. Compute the support reactions of the beam shown. Support at A is a roller and at B is a hinge. IIN 100N /m 30N/m 52N/m 1m 2m 3m 5m 4m 7m B
Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.
The assembly in figure shown consists of two A-36 steel rods (E = 29 x 103 ksi) and a rigid bar BD. Each rod has a diameter of %3D 0.65 in. If a force of 10 kips is applied to the bar, determine the angle of tilt in degrees of the bar. í 3 ft 2 ft B E D -1.25 ft- 0.75 ft 1 ft F 10 kip
Both elements have the same section and are made of the same material. Draw the shear and moment diagrams and draw the deformed Using matrix analysis techniques Realize the structural analysis (estimate forces in the supports and displacements in the free nodes) EI = 100.000 kn-m² I 10 m² H 12 m 20 N-m 目 8 40 kN 240 kw-m 2 12 m A