Beam ABCD2 is simply supported wth free end span at D to 2. The beam is subjected to various +ype of load as shown. According to this condition, answer the following questionS: D Check the adequacy of the beam section located at+ 3m away from pinned support Cpoint A) if the shear and momen+ resistances at that specified points are 33 KN and 90 kNm respectively. 2) Develop equations for shear and moment Covering the whole length of beam. Note: Use the reference point at pinned support. 3) Plot the shear force and bending moment diagrams ouer the length of beam, adndicate the location with highest moment. 20KN/m 36kN 50kN.m A E 2m 3m 2m + 6m

Beam ABCD2 is simply supported wth free end span at D to 2. The beam is subjected to various +ype of load as shown. According to this condition, answer the following questionS: D Check the adequacy of the beam section located at+ 3m away from pinned support Cpoint A) if the shear and momen+ resistances at that specified points are 33 KN and 90 kNm respectively. 2) Develop equations for shear and moment Covering the whole length of beam. Note: Use the reference point at pinned support. 3) Plot the shear force and bending moment diagrams ouer the length of beam, adndicate the location with highest moment. 20KN/m 36kN 50kN.m A E 2m 3m 2m + 6m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. 1. Draw the moment diagram for girder PQRST and column BGLQ of the building frame. All columns have the same cross-sectional area. N 10 ft 9 k F G H 10 ft 2. Determine the internal moment at A caused by the vertical loading. 10 ft C E 3. Draw completely the shear and moment diagram Fisntisat-20 -20 ft- 4. Compute the maximum deflection for the beam loaded as shown. Figure 1 2 k/ft 5 kN/m A B C D 18 ft 15 ft + 18 ft 9 KN/m Figure 3 400 lb 400 lb 160 Ib/ft 100 Ib/ft 10 ft 5 ft 5 ft 3 ft 6 ft + 3 ft R1 R2 R4 Figure 4 Figure 2 Diagnostic Exam
A beam with the cross-section shown is loaded in such a way that the maximum shear is 4.8 P kN and the maximum moments are 2.5 P kN-m and -3.6 kN+m, where is the applied load in kN. Determine the maximum safe value of P if the allowable shearing stress is 8MPa and the allowable bending stress are 30MPa in tension and 60MPa in compression.
Steel rails on a train track are laid with a small gap between them at a temperature of -25 F. The cross-sectional area of each rail is 5 in^2. The steel rails are 40-ft-long. a. When the temperature is increased to 95°F, determine 8. b. Using this gap, what would be the axial force in the rails if the temperature were to rise to 110°F?
The steel beam is fixed at A and supported by a roller at B. El is constant all throughout the beam. A. Determine the value of Modulus of Flexural Rigidity in kN- m^2 B. Draw the Shear and Moment Diagram of the given beam: 100mm - 王 10 mm 7.5 mm 100mm 10 mm 7 kN/m 14 kN A 3.5m BO 1.5m C
Problem 02. A propped cantilever beam having a span of 6 m is loaded with a uniformly distributed load of 12kN/m all throughout its unsupported length. Assume El is constant. Determine: a. The vertical reaction on the roller support in kN. b. The vertical reaction at the fixed-end support in kN. c. The horizontal reaction at the fixed end support in kN. d. The fixed-end moment in kN-m. e. The maximum deflection in terms of El. Note! A cantilever beam for which one end is fixed and other is provided support, in order to resist the deflection of the beam, is called a propped cantilever beam.
Value is 81 kN Kindly right legibly. Thank you.
USE FORCE METHOD OF STATISTICALLY INDETERMINATE STRUCTURE. Determine the reactions at the supports A, B, and C; then draw the shear and moment diagram. EI is constant. A. DEGREE OF INDETERMINANCY , NO OF REDUNDANT SUPPORTB. FBD DIAGRAM WITH CUTTING SECTIONS C. SOLUTIONS AND VALUE OF REACTIONS D. SHEAR AND MOMENT DIAGRAM
solve and show solution
3. The beam below is used to support a part of the overhang at the entrance of the building (a). The idealized model for beam with load is shown in (b). Assume that B is roller supported and C is simple supported. (a) Draw shear force (V-) and bending moment (M-) diagrams for the beam. Determine the position and value of maximum bending moment. (b) For the beam, assume HEA 180 for the type of cross section. Calculate the maximum normal stress and the maximum shear stress, and determine where in the cross section the normal and shear stresses are greatest. Utilize Appendix C at the end of the textbook.
Q.22 The loading, shear force and bending moment diagrams are given in the figure. Determine the position of point of contraflexure y from support B. (4) 21Nm- -In 5KN 30 in O 4KN tending diagram 2m SFD O AND IKN
STRUCTURAL ANALYSIS II