AB3 m1.5 mA. Draw the shear force and the bending moment diagrams, V and M for the simplysupported beam under the given loading condition.B. If the beam is subjected to the internal moment of M forming an angle of 600 with thehorizontal z axis as shown in the beam cross section, determine the maximum bendingstresses acting over the cross section (at points A and B) and the orientation of theneutral axis.Beam cross sectionMy100 mm60M100 mm50 mm12 kN/mA50 mm200 mm2.60°BA

Given angle = 60 deg UDl = 12kn/m

B 3 m 1.5 m A. Draw the shear force and the bending moment diagrams, V and M for the simply supported beam under the given loading condition. B. If the beam is subjected to the internal moment of M forming an angle of 60⁰ with the horizontal z axis as shown in the beam cross section, determine the maximum bending stresses acting over the cross section (at points A and B) and the orientation of the neutral axis. Beam cross section M A 100 mm z-ft 60° 60 M 100 mm 12 kN/m A 50 mm 200 mm

B 3 m 1.5 m A. Draw the shear force and the bending moment diagrams, V and M for the simply supported beam under the given loading condition. B. If the beam is subjected to the internal moment of M forming an angle of 60⁰ with the horizontal z axis as shown in the beam cross section, determine the maximum bending stresses acting over the cross section (at points A and B) and the orientation of the neutral axis. Beam cross section M A 100 mm z-ft 60° 60 M 100 mm 12 kN/m A 50 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Nearest Ans - 148 N.m
A beam is subjected to equal bending moments of M, = 3300 N-m. The cross-sectional dimensions are b = 175 mm, c = 31 mm, d = 74 mm, and t = 5 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M2 M2 H d (typ) K b Answer: (a) y= i mm 1z = i mm4 S= i mm3 (b) OH = i MPa ( c) σκ-i MPa (d) Omax MPa
The cross-sectional dimensions of a beam are shown. Assume b-1.875 in., t-tw-0.125 in. and d=2.75 in. (a) If the bending stress at point K is 3340 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o, at point H (positive if tension, negative if compression). H K Answers: bf (a) M₂ = i (b) σH = tw lb-ft. psi.
Solve using Moment -Area Method. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminium rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I= 50 x 10° mm* for the beam, Eal = 70 GPa, and A = 42 mm? for the rod. - Aluminum 5 m -Steel A C m m
A steel beam is of cross section of right triangle of dimension 40 mm wide and 60 mm wide and 60 mm depth having yield point stress f, = 280 N/mm?. Evaluate the fully plastic moment for the condition that the neutral axis passes through point B as shown in the figure below and divides the right triangle into two equal triangular parts. Assume that the plane of the load passes through the centroids of two triangles thus created. 40 mm A. 60 mm
statically indeterminate structures using force method
d=450 mm
really really need
Q.4) A pipe assembly is acted on by four forces and one couple moment. The 300 N force is parallel with the z-axis, the 130 N force is parallel with the y-axis, and the 60 N force is parallel with the x-axis. Force F, has a magnitude of 220 N and coordinate direction angles given by aA = 45°, BA = 60°, and YA = 120°. The couple moment M, is in the x-z plane and has a magnitude of 400 N-m. Determine the resultant moment about point B. Mc 30 300 N 1 m B0.5 m 0.75 m 0.75 m 130 N FA
The A-36 steel beam has a depth of 10 in. and is subjected to a constant moment M0, which causes the stress at the outer fibers to become sY = 36 ksi. Determine the radius of curvature of the beam and the beam’s maximumslope and deflection.
The moment acting on the cross section of the unequal-leg angle has a magnitude of 19 kN-m and is oriented as shown in the figure. All stresses are positive if tensile and negative if compressive. Assume a = 180 mm, b- 125 mm and t- 17 mm. Determine (a) the bending stress at point H. (b) the bending stress at point K. (c) the maximum tension and the maximum compression bending stresses in the cross section. (d) the orientation B of the neutral axis relative to the +z axis. b. y K H. (typ.) Answers: (a) OH = i MPa (b) OK = MPа (c) OmaxT = MPa OmaxC = MPa (d) B = i
A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following unknowns if the modulus of elasticity is 160GPa and the maximum deflection is -0.63254616477273mm. BEAM'S DIMENSION: Width = 110mm , Height = 480mm NOTE: L = 3m Solve the maximum moment of the beam. Answer for part 1 kN-m Determine the shear at midspan.