Based on the given chromatograph, answer the following questions: 1) Which of the diet sodas have the highest concentration of caffeine? Which standard best reflects this concentration? 2) Which of the diet sodas have the lowest concentration of aspartame? Which standard best reflects this concentration? 3) What is the approximate retention time of benzoate?

Based on the given chromatograph, answer the following questions: 1) Which of the diet sodas have the highest concentration of caffeine? Which standard best reflects this concentration? 2) Which of the diet sodas have the lowest concentration of aspartame? Which standard best reflects this concentration? 3) What is the approximate retention time of benzoate?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

An experiment is started with 6g of a 1:1:1 ratio mixture of benzoic acid, 2-naphthol, and hydroquinone dimethyl ether. The experiment is finished with 0.2 g of 2-naphthol. What is the percent recovery? 10% 50% 3% 16%
Magnesium is used in alloys, in batteries, and in the manufacturing of chemicals. It is obtained mostly from seawater, which contains 1.3 g of magnesium for every 1.0 kilograms of seawater. Calculate the volume of seawater in liters needed to extract 8.0 x 104 tons of magnesium, which is roughly the annual production in the United States. given information: density of seawater = 1.03 g/mL ; 1 Kg = 2.21 lb ; 1 ton = 2000 lb
▪ In a blood alcohol analysis by GC-FID, methanol elutes at 1 min, ethanol at 2 min, IPA at 3 min, and IS at 4 min. In the patient sample, the analyte elutes t 2 min and the IS at 8 min. What is the relative retention time and the analyte in the patient? ▪ A) methanol B) Ethanol ▪ C) IPA
A scientist wishes to measure the concentration of methyl benzoate in a plant stream by gas chromatography. He prepares a sample of butyl benzoate to use as an internal standard. The results of a preliminary run, which used a solution known to contain 1.37 mg/mL of methyl benzoate (peak A) and 1.51 mg/mL of butyl benzoate (peak B), are shown. The area of peak A is determined to be 3.40×102 and the area of peak B is determined to be 398 measured in arbitrary units by the computer. To measure the sample, 1.00 mL of a standard sample of butyl benzoate containing 2.49 mg/mL is mixed with 1.00 mL of the plant stream material. Analysis of the mixture gave a peak area of 437 for peak A and 415 for peak B. What is the concentration of methyl benzoate in the plant stream?
Question 28
In this experiment you will use 5.20 g of Ph3P+CH2CO2Et Br–. How many millimoles is this?
If a pharmacist fortified 10 g of a 0.1% w/w tacrolimus (PROTOPIC) ointment by adding 12.5 g of an ointment containing 0.03% w/w of the same drug, what would be the percentage strength of the mixture?
what is the specific gravity of a substance that displaeces 1.2ml and has a mass of 5.021g
6.0 mL of cyclohexanol, 8 mL of 85% phosphoric acid, and 10 drops of sulfuric acid are added to a 50-mL round-bottom flask with boiling chips, and the mixture is distilled into an ice-cooled receiver. The distillate is in the form of a colorless bi-phasic mixture. The cyclohexene upper layer is removed from the water layer, and dried over anhydrous calcium chloride. Isolated is cyclohexene as a clear and colorless foul-smelling liquid. Weighing data is given below. Gross mass: 51.24 g Tare mass: 48.04 g Product mass: 3.2g Question: Calculate the theoretical mass of the cyclohexene product, bearing in mind that the cyclohexanol starting material was measured by volume, not by mass (so you must use the density of cyclohexanol to convert milliliters to grams, before calculating the number of moles). Calculate the percent yield of cyclohexene obtained.
Sample # 1 2 0.2425 0.2160 0.2274 Weighed mass of ascorbic acid (g) volume of KIO3 (mL) 18.86 17.91 17.37 0.02459 0.02462 0.02432 [KIO3] (mol L-1) Mean [KIO3] (based on titration) 0.02451 mol L-1 Standard deviation in the mean [KIO3] mol L-1 Confidence limit for the [KI03] mol L-1 Relative confidence limit for the [KIO3] ppt =
Method of Standard Addition Worksheet You are provided a stock standard solution containing : 0.0500 g/250 mL acetaminophin (APAP). You need to determine how much standard stock is required to prepare the following solutions using 100 mL flasks. Flask 12 3 4 [APAP] added ppm (mg/L) t 10 20 30 40 RI mL Stock 0.1 What method of calibration do you use if you are analyzing a product and the product contains no ingredients that interfere with the instrument response for APAP in the product? on th LI What method of analysis do you use if you are analyzing a product and the product contains ingredients that interfere with the instrument response for APAP in the product? or
© Macmillan Learning Five standard solutions of a newly discovered inorganic salt were used to create a calibration curve. The density (g/mL) of each solution was plotted on the y-axis versus the % (w/v) concentration on the x-axis. The calibration curve was linear and fitted with the following best-fit line. y = 1.17x + 0.188 A student is asked to analyze a solution of this salt with a density of 4.00 g/mL. What is the concentration, in %(w/v), of the unknown salt solution? concentration: % (w/v)