B. Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is h = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)

B. Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is h = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3/ The pipe has a different diameter: diameter (Di = 4 m) changes into (D2 = 6 = 6 m/s). m). The water velocity in the entrance profile was measured (v1 Calculate the discharge and leave velocity (see figure). Determine also type of flow in input pipe (whether the flow is laminar or turbulent). D,
Note: Unless otherwise stated, take the density of water to be p = 1000 kg/m³ and atmospheric pressure, Patm=101.3 kPa. Water from a reservoir passes through a pump to an open air. A static manometer is attached to the pipe. The head loss along pipe A and pipe B is 1.2 m and 3.8 m respectively. i. Find the power consumed by the pump if the pressure gauge reads 750 kPa. Find the pressure just before the pump suction point. ii. Assume that the pump is 100% efficient. Pipe B diameter: 40 cm Nozzle diameter: 7.6 cm Mercury SG 13.6 2.5 cm Pump 2.4 m Static pitot manometer Pressure gauge Pipe A diameter: 30 cm Air Water
Fluids
= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
As fast as. Don'r Hold please.
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
Find the power (kW) if the area is 2.5 m2 and the head is 5 meters if water is running at 8 m/s.
Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.
8. In the figure below a manometer uses oil with specific gravity of 0.8. (a) Calculate the discharge when R = 1 ft. (b) Repeat the problem if the pipe is inclined at 30° upward. oil R 6" 3" -- 6"
In a hydraulic system, the power is measured as 52 X 10-2 Kilo joules per seconds and pressure is given 320.6 x10-3 N/m2 .Find the flowrate of the hydraulic system.
P₁ = 80 kPa B 3 m PB = 50 kPa Calculate the friction head loss for a water Q-1 flowing from point A to B.
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.