B. Determine the LRFD design strength and ASD allowable strength of the sections given.1. A36 steel and 7/8"-diameter bolts- L6 x 34 x3 in3 in 4 in 4 in2. An A36 C9 x 20 with 2 lines of 7/8-in diameter bolts in the web as shown in the figure.2 in34 in2 inC9 x 203 in'3 inTo1/22.

B. Determine the LRFD design strength and ASD allowable strength of the sections given. 1. A36 steel and 7/8"-diameter bolts L6 x 3 x 2 in 3 in I 3 in 4 in 4 in 2. An A36 C9 x 20 with 2 lines of 7/8-in diameter bolts in the web as shown in the figure. 2 34 in C9x 20 3 in 3 in

B. Determine the LRFD design strength and ASD allowable strength of the sections given. 1. A36 steel and 7/8"-diameter bolts L6 x 3 x 2 in 3 in I 3 in 4 in 4 in 2. An A36 C9 x 20 with 2 lines of 7/8-in diameter bolts in the web as shown in the figure. 2 34 in C9x 20 3 in 3 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION 1 The tension member shown in the figure contains holes for 1-in Ø bolts. At what spacing,…

Q: 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy-36ksi, Fu=58ksi…

A: Given Data: A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole…

Q: Select a W section bolted as shown in Figure 6.12 with %-in.-diameter bolts, and three bolts per…

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: For the A36 beam shown in the accompanying illustration, what is the required spacing of 7/8-in A307…

A: Consider the free body diagram;

Q: What is the Nominal Shear Capacity of the following shear splice 3/4" A325N bolts W18x35 W24x55 F1…

A: Anb = 3.14 x (3/4)2 = 1.76625 sq inch fu = 105ksi FOS = 1.25

Q: B) The tension member shown in Figure is a W 16 × 40, and the steel is A992. The bolts are 3/4-inch…

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: Possible Failure Modes of Bolts in Shear, Tension, and Combined LoadingBolts are critical components…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: 7. Compute the tensile capacity for the A36 steel plate shown. Bolts are 7/8 in diameter. Neglect…

A: For A36 steelUltimate Tensile Strength, fu = 58,000 psiYield Tensile Strength, fy = 36,300 psiThe…

Q: 2. Compute the design strength in tension, P, of the A36 steel plate (1/4 in x 12 in) with a line of…

A: Compute the design strength in tension, Pn, of the A36 steel plate (1/4 in 12in) with a line of…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: ## Potential Failure Modes of Bolts in Shear, Tension, or Both**Understanding Bolt Failure**Bolts, a…

Q: the subject is steel strucure

A: Here's an outline for designing the floor slab with the given parameters and compiling the…

Q: 2. PLATE WITH STAGGERED BOLTS Compute A and A for a 14-in.-wide and 2-in.-thick plate subject to…

Q: a. Prepare a table showing values of Group A bolt shear strength and slip-critical strength for…

A: Shear strength: The maximum load that can be resisted by the structure is known as shear strength.…

Q: Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure,…

A: LFRD stands for Load Resistance Factor Design, it is a method of designing concrete and steel…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: 9.4 An L 8 x 4 x ½ has staggered holes for %-in. diameter bolts, as shown in Figure P9.4. Determine…

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: 3. Based on the figure below, are the threads to be considered included on the shear plane? Why?…

A: From the figure it can be observed that the shank (shown in figure below) of the bolt is ending…

Q: Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a…

A: The thickness of the plates = 10 mm The connection provided = 6-16 mm bolts The yield strength of…

Q: The L7 x 4 x 1/2 single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: Calculate the minimum girder width to fit the longitudinal bars shown that have center-to-center…

A: Given data: Total depth of the beam, D=20 in Diameter of main reinforcing bar,d=98=1.125 in Center…

Q: ple shear stress FT = 207 MPa. Use A36 steel with yield strength Fy = 248 MPa and a minimum tens h…

A: According to given data A butt joint is bolted using A325 bolts with a diameter of 22mm, with…

Q: Compute A,, and A, for a 14-in.-wide and ½-in.-thick plate subject to tensile loading with staggered…

A: Given : Width = 14 inches Thickness = 1/2 inches Compute An and Ae for the given plate ?

Q: Solution accu

A: Approach to solving the question:Understand the concept of net area: The net area is the effective…

Q: 6. Given a sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts, answer…

A: A sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts.Need to finda.…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: 9.0 A C12 x 30 is connected with 25 mm diameter bolts in each flange, as shown. If Fy= 345 MPa, Fu=…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Question

100%

B. Determine the LRFD design strength and ASD allowable strength of the sections given.
1. A36 steel and 7/8"-diameter bolts
- L6 x 34 x
3 in
3 in 4 in 4 in
2. An A36 C9 x 20 with 2 lines of 7/8-in diameter bolts in the web as shown in the figure.
2 in
34 in
2 in
C9 x 20
3 in'3 in
To
1/2
2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 3/4" x 10" X 5' long plate is fabricated from A36 steel and has standard holes for 3/4" bolts at each end for attachment to other structural members. The figure below shows a face view of the plate. The service loads that the member will be subject to are 140 kips of dead load and 30 kips of live load. Calculate the factored load, tensile yield strength and rupture strength. Compare the results to the factored loads and comment. Ignore block shear. + 3" 3" + 3" **- 1 1/2" 10" 5' SYM 5
Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in Ø bolts at the usual gage locations. The stagger is 1 1/2 in. (Ans. 2.98 in^2)
1. answer basing with the new NSCP 2015 guideline codes
Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes are 2 in O 3 in 3 in 4 in 3 in 2 in PL 7/8 x 12 12 in-
how to solve ?? please and thank you.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
In mm) Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure, Problem 11. If Fy = 345MPA, Fu = 450MPA, and Ae = 0.90An, Apply the following %3D %3D %3D approaches to determine: a. The design strength for LRFD. b. The allowable strength for ASD. Section Figure. Problem 8
The tension member shown in the figure is connected to a gusset plate as shown with 1.210-inch diameter bolts. It is subjected to the dead and live loads as shown. Take Fy = 33.29 ksi and Fu = 52.93 ksi. Assume Ae = An. a) Draw the critical cross-section and show its dimensions using your data. b) Determine whether this member has enough strength using LRFD and the critical ASCE 7 loading combination.
4. Given a sheared flat bar 5" in width, which is to have a double line of 3/4" Dia bolts, answer the following. a. Does the bolt hole pattern need to be staggered? b. What is the minimum edge distance required? c. What is the gage distance? d. What is the clearance "E" required? e. What is the diagonal minimum distance? f. What is the minimum pitch?