(B) Q: The cantilever beam shown below has a circular cross section of 50mm outer diameter. Portion AB of the beam is hollow, with an inner diameter of 35mm. If the allowable bending stress is 140 MPa, determine (1) the largest allowable uniformly distributed load (w) that can be applied to the beam; (2) the bending stress at a point that is 7 mm below the top of the beam at section D. 50 mm W D B O 35 mm A 750 mm 250 mm

(B) Q: The cantilever beam shown below has a circular cross section of 50mm outer diameter. Portion AB of the beam is hollow, with an inner diameter of 35mm. If the allowable bending stress is 140 MPa, determine (1) the largest allowable uniformly distributed load (w) that can be applied to the beam; (2) the bending stress at a point that is 7 mm below the top of the beam at section D. 50 mm W D B O 35 mm A 750 mm 250 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hs
A 50 mm diameter circular bar is used as a simply supported beam 10 m long, is simply supported at the left- hand end and at its mid- point. it carries a uniformly distributed load of 48 KN/m between the supports and a point load of 50 KN at the right- hand end. Determine : (a) draw shear force and moment diagrams. ( b) flexural * .stress
As the safe normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross-section height (mm) of the beam.
The internal shear force V at a certain section of an aluminum beam is 8.7 kN. If the beam has the cross section shown (assume a=44 mm, b=87 mm, tw=t=4 mm, d=88 mm), determine: (a) the shear stress ty at point H, which is located 44 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. bf H a Answers: (а) тн — i MPa. (Б) тmах — i MРа.
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 70 GPa] bar, as shown. The beam is subjectedto a bending moment of 2140 N-m acting about the z axis. Assume b=44 mm, d =50 mm, d =10 mm. Determine:(a) the maximum bending stresses , in the brass plates and the aluminum bar.(b) the stress in the brass at the joints where the two materials are bonded together.
Straight 0.30 in. Diameter and 20 feet in length are often used as duct cleaning for an obstruction pipe or for introducing wires through new conduit. The rushes are made of high-strength steel and, for storage and transport, are wound onto 5-foot diameter spools. Assuming that the yield point is not exceeded, determine (a) the stress in an exceeded run, that is, the corresponding bending time in the rush. Use E = 29 x 106 psi. 5 ft
A 50 mm diameter circular bar is used as a simply supported beam 3 m long. Applied the uniforme distributed load ( 600 KN/m ) over the right two - thirds of the beam. Determine: (a) draw shear force and moment diagrams. ( b) SO RS
The beam consists of a W24 x 94 structural steel wide-flange shape [E = 29,000 ksi; I = 2,700 in.“). For the loading shown, determine: (a) the reactions at A and D (positive if the force is up, and the moment counterclockwise). (b) the magnitude of the maximum bending stress amax in the beam. Assume LAB = LBC =7 ft, LcD = 13 ft, w = 4.3 kips/ft, P = 41 kips. B D LAB LBC LCD Answers: (a) A = kips, D= i kips, Mp = kip-ft. (b) ơmax = ksi.
A beam of circular cross-section has a length of 5m and is simply supported at its ends. It is required to carry a total load of 57 kN uniformly distributed over the whole length. If the maximum bending stress is not to exceed 13 MPa and the maximum deflection is limited to 4 cm, the diameter of shaft in mm is given by : (take E= 18 GPa.)