A cantilever timber beam with a span of L = 3.1 m supports a uniformly distributed load w. The beam width is b = 280 mm and the beamheight is h = 200 mm. The allowable bending stress of the wood is 7 MPa. Determine the magnitude of the maximum load w that maybe carried by the beam.Answer: w=LiBbkN/m.

GivenL=3.1mb=280mmh=200mmσ=7MPa

A cantilever timber beam with a span of L = 3.1 m supports a uniformly distributed load w. The beam width is b = 280 mm and the bea height is h = 200 mm. The allowable bending stress of the wood is 7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. A L B b h

A cantilever timber beam with a span of L = 3.1 m supports a uniformly distributed load w. The beam width is b = 280 mm and the bea height is h = 200 mm. The allowable bending stress of the wood is 7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. A L B b h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The simple beam AB, shown below, supports a concentrated load of 6 kN and a segmentof non-uniform load of intensity varies from 1 kN/m to 3 kN/m at point B. a). Determine the maximum bending stress and the maximum shear stress acting on the beam if the beam has a rectangular cross section of (500 mm × 200 mm).
The steel beam has the cross section shown. The beam length is L = 17 ft, and the cross-sectional dimensions ared = 15.5 in., b; = 10.7 in., t = 0.635 in., and tw = 0.340 in. Calculate the maximum bending stress in the beam if wo = 4.7 kips/ft. B Answer: Omax ksi
As the safe normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross-section height (mm) of the beam.
The cantilever beam AC shown in the figure is subjected to a load 1kN at the end A, and an in- plane clockwise moment 5 kNm at B. The shear force and bending moment in the beam at C are respectively, 1 kN 2 m 3 m O a. (-)1 kN, 0 Ob. 1 kN, 5 kNm OC. 1 kN, (-)5 kNm Od. (-)1 kN, 10 kNm
ASAP
The T-beam is made from two plates welded together as shown. Determine the maximum uniform distributed load w that can be safely supported on the beam if the allowable bending stress is allow = 159 MPa and the allowable average shear stress is Tallow = 71 MPa. [w = 11.4 kN/m] A -1.5 m -1.5 m- 200 mm T 20 mm 200 mm 20 mm
A beam is simply supported on a span of 10 m. The beam supports a load of 15 kN/m on its entire length and three 30 kN loads at its quarter points. If the maximum bending stress is equal to 250 MPa, determine the most economical W-shaped beam. OW 530 x 72 O W 510 x 70 O W630 x 65 O W440 x 83
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. note ; Please solve number 3.4.5.6.7 i) Reaction force at B = 33.4N ii) Reaction Force at A = 18.6N iii) The distance from B at which the shear Force value changes from "-" to "+" = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
For the beam shown below, calculate the minimum value of b considering that allowable normal stress and shear stress for the material used are 12 MPa and 825 kPa, respectively. 2.4 kN 4.8 kN B CY A D 150 mm
A beam of circular cross-section has a length of 5m and is simply supported at its ends. It is required to carry a total load of 57 kN uniformly distributed over the whole length. If the maximum bending stress is not to exceed 13 MPa and the maximum deflection is limited to 4 cm, the diameter of shaft in mm is given by : (take E= 18 GPa.)
For the structure shown has a load of W = 7 kips /ft and P = 20 kips , (a) Determine the shear and bending moment diagrams for the beam and it’s loadings. (b) Determine the normal stress at section just left or just right of point D.