Problem 4.1 A simply supported beam carries a distributed load of 10 kN/m over a span of 5 m and a concentrated load of 10 kN at pint A and 8 kN at pint D, as shown in the figure below. Determine: 1. The Shearing Force and Bending Moment Diagrams for Fig. (a). 2. The maximum bending stress set-up on the beam. The beam section is shown in Fig (b). 10 kN 8 kN 20 mm 20 mm 20 mm 10 kN/m A |D C 0000 1 m '40 mm 20 mm 1 m 3 m 20 mm (а) (b)

Problem 4.1 A simply supported beam carries a distributed load of 10 kN/m over a span of 5 m and a concentrated load of 10 kN at pint A and 8 kN at pint D, as shown in the figure below. Determine: 1. The Shearing Force and Bending Moment Diagrams for Fig. (a). 2. The maximum bending stress set-up on the beam. The beam section is shown in Fig (b). 10 kN 8 kN 20 mm 20 mm 20 mm 10 kN/m A |D C 0000 1 m '40 mm 20 mm 1 m 3 m 20 mm (а) (b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the beam loading system given below, A is a simple and C is a sliding support. The outer diameter of the beam with a tubular profile is 180 mm, while the inner diameter is 140 mm. (a) Draw the normal stress distribution in the section at point B. (b) Draw the normal stress distribution in the cross section at the support C. (c) Find where the maximum stress occurs. 8 kN/m 12 kN 10 kN A B 2.5 m 2.5 m 3.0 m to
A 50 mm diameter circular bar is used as a simply supported beam 10 m long, is simply supported at the left- hand end and at its mid- point. it carries a uniformly distributed load of 48 KN/m between the supports and a point load of 50 KN at the right- hand end. Determine : (a) draw shear force and moment diagrams. ( b) flexural * .stress
Calculate the shear force V (in kN) and bending moment M (in kN - m) at a cross section located just right of the 4 kN load on the cantilever beam AB shown in the figure. (Use the deformation sign convention.) | 4.0 kN 1.4 kN/m 3.9 m 3.9 m 7.8 m V = 10.92 v kN M - -85.2 kN m
A beam is partially loaded with a uniform load of 2 kN/m and a point load of 2 kN as 2 kN 2 kN/m shown below. A B i. Determine the support reaction forces. Draw the Shear Force Diagram using analytical equations. Draw the Bending Moment Diagram using analytical equations. iv. ii. 3 m 2 m iii. Assume beam has a square cross section, dimension the beam cross section as maximum allowable bending stress is given Oall=50 MPa
Pravinbhai
Question 1) F=35 kN single load, M=45 kN.m moment and w=16 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is also given as L=4 m. The cross-sectional properties of the beam are; body height yg=225 mm, body thickness xg=14 mm, flange width xf=194 mm, flange height yf=11 mm. Point P on the section is located just above the flange-body junction. It is desired to determine the stress state at the P point in the section taken from the B line of the beam. According to this;Question1-A) Find the shear force (VB) at point B. (Write your result in kN.)Question1-B) Find the bending moment (MB) at point B. (Write your result in kN.m.)Question 1-C) Find the moment of inertia of the beam section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005.)
strength of materials
Find the cross sectional dimensions of the smallest square beam that can be loaded as shown in the figure if the allowable shearing stress is 1.0 MPa and the allowable bending stress is 8 MPa. 6 kN 14 kN m 1 m 2 m 3 m
Q3: For the load diagram shown in figure (2) below, the first contraflexure point of the bending moment diagram is located at ...... m from A. 50 KN 2m D 60 kN/m 4m Figure (2) K40 2 m 8 kN.m
7.16 The figure shows a steel beam which is fixedly clamped in A, and which rests on a roller bearing in B. The beam is 5 meters long, and is loaded with a bending moment of 25 kNm at the end. Determine the stock reactions in A and in B. 25 kNm 2,5 m 2,5 m
Q4 A solid rectangular homogeneous section (total length = 7.2m) is simply supported, where b = 50 mm and d = 175 mm. A concentrated load F= 140 N acts at point C where L1= 4.00 m L2 = 3.20 m. Calculate the maximum bending stress and give your answer in N/mm² to 2 decimal %3D places. *Assume the weight of the beam is negligible and zero. F 200. L1 L2 b d A F B
A horizontal beam AE, 12 m long and it carries a uniformly distributed load of 3.8 kN/m over the full span and a point load of 4 kN at the left-hand end A. The beam is simply supported at B, 2 m from A center of the beam. 2.1 Draw the shear force and bending moments diagrams for the beam and 2.2 Determine the position of the Contraflexure points. 6 kN 4 kN 4 kN 8 kN/m A 1 m 4 m 1 m 1 m Rp= kN Re kN X-