(B) A vertical cylinder 1.5m height and 18 cm in diameter is maintained at 100°C in an atmosphere environment of 20°C. Calculate the heat loss by free convection from the surface of the cylinder. Use the following data: p=1.06 kg/m v = 18.97×10° m/s, k=0.1042 W/mK and Pr-0.6975 1/3 Nu =0.1 (Ra)3

(B) A vertical cylinder 1.5m height and 18 cm in diameter is maintained at 100°C in an atmosphere environment of 20°C. Calculate the heat loss by free convection from the surface of the cylinder. Use the following data: p=1.06 kg/m v = 18.97×10° m/s, k=0.1042 W/mK and Pr-0.6975 1/3 Nu =0.1 (Ra)3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can someone please help me to solve all of the following question showing all work and explanation as well as graphs needed in excel with formulas. Thank you!
i need the answer quickly
= A long rod of 60-mm diameter and thermophysical properties p 8000 kg/m³, c C = 500 J/kg-K, and k = 50 W/m-K is initially at a uniform temperature and is heated in a forced convection furnace maintained at 750 K. The convection coefficient is estimated to be 1000 W/m².K. What is the centerline temperature of the rod when the surface temperature is 570 K? The centerline temperature of the rod is i K.
Required information Consider a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as given in the figure. The thermal conductivities of various materials used, in W/m-K, are kA=kF=2, kg-8. kc-20, kp=15, and ke-35. The left and right surfaces of the wall are maintained at uniform temperatures of 345°C and 100°C, respectively. Assume heat transfer through the wall to be one-dimensional. Disregard any contact resistances at the interfaces. 1 cm. A4 cm B 4 cm रेव 4 cm Sem 6 cm DI 4 E 6 cm F 10 cm 6 cm 100°C 8m Determine the rate of heat transfer through the wall (in W).
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at T = 40°C and the 30 W/m2-K, what are corresponding convection coefficient is h; the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is To || 0,0 -30°C and the associated convection coefficient is ho W/m2-K? Evaluate the properties of the glass at 300 K. = 65 Tsi i °C Ts.0 °C T5,0 i
In the arctic sea, the ice sheets are melting. Let's calculate the temperautre distribution in one such ice sheet. The sheet is 2 m thick. Under the sheet there is ice-water mixture and it can be assumed that the temperature of the bottom surface of the ice sheet is approximately 0°C. Air at -20°C is blowing above the sheet. The convection coefficient of air is 15 W/m².K. The thermal conductivity of ice is 2.2 W/m.K. What is the temperautre of icesheet at its center (i.e., at 1 m from the surface)?
Solve it correctly please. I will rate accordingly with 4votes but I need correct answer.
Heat transfer
The main body of plenum is a steel vessel of diameter 0.1meters has two semicircle domed ends. During operation is will contain mix of fuel and air at approximately 250OC. The wall of the vessel is 0.03meters thick and the plenum is 0.45meters long. Estimate the rate of heat loss from the vessel when the outside air temperature is 45OC. The thermal conductivity of steel is 45 W/m K and the surface heat transfer coefficient on the air side is 8 W/m2 . On the inside it is 65W/m2 . If it was possible to clad the plenum calculate the reduction in the rate of heat loss. Assume the lagging would be 5mm thick and has a thermal conductivity of 0.05 W/m.
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at Ti = 40°C and the = 30 W/m2-K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick corresponding convection coefficient is h; window glass, if the outside ambient air temperature is To = -15°C and the associated convection coefficient is h, = 65 W/m²-K? o,0 Evaluate the properties of the glass at 300 K. Tsi i °C Ts,0 i °C
Can you help me answer my sample problem for my review?
In a manufacturing process, a long 20 cm diameter rods of stainless steel (k = 14.9 W/m.K, p = 7900 kg/m³, c = 477 J/kg.K) are at a uniform temperature of 600°C in a curing oven, from which they are removed and cooled by forced convection in air at 200°C and convection coefficient of 45 W/m2.K. (a) How long does it take for the rod to have a minimum temperature of 360°C? (b) Calculate the maximum temperature at that time?