Assume a steel pipe of r, = 10 mm, exposed to natural convection at h = 50 W/m².K. This pipe is insulated by the material of thermal conductivityk = 0.5 W/m.K. Determine the critical thickness of this combination: %3D

Assume a steel pipe of r, = 10 mm, exposed to natural convection at h = 50 W/m².K. This pipe is insulated by the material of thermal conductivityk = 0.5 W/m.K. Determine the critical thickness of this combination: %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.22P

See similar textbooks

Related questions

Q: Given data : m-20 kg g-10 m/s2 h-2 m Find Potential energy

Q: 1I. Determine the reactions at supports. P-20 kN 98 kN/m 4m 3. 4 m 4 m 3 m

Q: What weld section properties are required to analyze the weld between the horizontal tube and the…

Q: Find maximum shear stress Maximum principal stress-8 MPa Minimum principal stress=3 MPa

A: Given data : Maximum principal stress=σ1 Minimum principal stress=σ2 To find : Maximum shear…

Q: a open cycle and a closed cycle gas turbine engine.

A: Difference between An open and a closed cycle gas turbine engine

Q: Find the transfer Function of this translational Mechanical system X2 (t) X1(t) f(t) 2N m oll M1 X1…

Q: What is the total degree of freedom (DOF) of the mechanism shown in the figure? DO 3.

Q: Water is discharging out of a tank via a pipe with length L = 4.2 m and diameter D= 3.5 cm into an…

Q: Completely solve and provide the diagram. Box the final answers. Use 4 decimals in all instances.…

A: Given:- T1=300 K,P1=101.325 kPa,P2P1=4,T3=1150 K,ηmech,C=.87,ηC=.92,ηmech,T=.80,ηgen=.96,Calorific…

Q: A billboard is supported by a rectangular post as shown. The weight of the W, is centered on the…

Q: 2. A spring of stiffness k = 500 N/m is mounted against the 10-kg block. If the block is subjected…

Q: A rocket is launched vertically at time t = 0. The elevation of the rocket is given by y = –0.14t^4…

A: Find the maximum velocity and elevation.

Q: The stream function of a flow field is ų = Ax3 – Bxy², where A = 1 m-1s1 and B = 3 m1s1. (a) Derive…

A: The velocity along the x axis can be determined as shown below.

Q: Find the Shear Moment Diagram of the following problems using

Q: A constant density bar with mass m and ler in place as shown. Use the usual x,y,z oo the following…

Q: The 10.0-lb block rests on a surface for which uk = 0.500. It is acted upon by a radial force of…

A: (A) The applied force along the radial line can be determined as shown below.

Q: The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50…

A: (a) Cylinder walls: ◆ Longitudinal stress = 68.25 MPa. ◆ Circumferential stress = 136.50 MPa. (b)…

Q: What are the sources of error and how can one minimize the error?

A: Measurement error is a common inaccuracy which takes place when on is conducting an experiment.…

Q: associated rotating parts has a moment of inertia of 50 kg m2. The angular acceleration of the shaft…

Q: A car is moving on a straight road 20 m/s. It is acceleration at 34 m/s?. What will be it's velocity…

Q: Can you also show the plot on the chart provided? The mass flow rate of the refrigerant in a…

A: Given DataTE=-20°CTc=50°Cm˙=0.016kg/s Using the above table and using also steam table for taking…

Q: As a thermo-fluid engineer working for an energy startup located at Greentown Labs, you are tasked…

A: Given Inlet temperature of hot gas, Ti = 52oC Inlet temperature of cold water, T1 = 4oC…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to…

Q: harles' law states that If the pressure on a particular quantity of gas is held constant, then, with…

Q: What is the y component of a force with magnitude of 5kn applied 120 degrees with respect to the…

Q: Within an air-handling system, a stream of air at T=30°C and 91=40% relative humidity is being mixed…

Q: 5. 20 Give in detail biomechanical analysis of walking gait.

A: A person's gait is their walking pattern. Walking requires muscular coordination and balance to…

Q: Circuit Problem and Description: Using the given components, design two pneumatic circuit which will…

A: Given : 2 Circuit description To find : Circuit diagram

Q: Deterime the Normal force on crate whose mass is 28 kg resting on horizontal surface

Q: Circuit Problem and Description: Using the given components, design a pneumatic circuit which will…

A: Given : Circuit description To find : Circuit diagram

Q: (b) State THREE (3) differences between cold working and hot working processes.

A: Deformation of the material will be done at a temperature less than recrystallization temperature is…

Q: You have been asked by your engineering company to design a complete gear and shaft system shaft…

A: Given:- TA=15 kN-m(clockwise direction),TB=30 kN-m(clockwise direction),TC=75 kN-m(anti-clockwise…

Q: ons are in mm) O2A AB BC AC CD 30 50 30 60 100 60 30 C BO4 0204 140 02 04 30.00 e velocity of C?…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: A jet of water, 10 cm diameter and having a velocity of 15 m/s impinges at the centre of a…

Q: Determine C (the number of components), P (the number of phases) and F (the variance) of the system…

A: Under equilibrium circumstances at constant pressure, the Gibbs phase rule p+n=c+1 gives the…

Q: Question 8 – Linearization and the Transfer Function Linearize and determine the transfer function…

Q: Problem. If the force applied is perpendicular to the handle of the spanner as shown in the diagram,…

Q: A car is moving on a straight road 20 m/s. It is acceleration at 34 m/s? What will be it's velocity…

A: Given data : Acceleration=a Initial velocity=U time=t Find : Final velocity after 6 s

Q: A schematic of a clutch-testing machine is shown. The steel shaft rotates at a constant speed w. An…

A: Torsional loading Those load which imparts the turning moment or the torque, is known as…

Q: In (Eigure 1). P 65 lb The pin at Cis attached to member ABCD and passes through the smooth slot in…

A: Given data, Applied force, P = 65 lb To determine:- a) Horizontal and vertical force at pin A b)…

Q: Deterime the Normal force on crate whose mass is 28 kg resting on horizontal surface

A: Given data : Mass of crate=m Acceleration due to gravity=g To find : Normal force on crate

Q: Problem 3. A circular cylindrical shaft composed of three materials is subjected to axial loads of P…

Q: Q2) Solve Laplace's equation to determine the steady state temperature u(x,y) in the semi-infinite…

A: The steady-state temperature distribution in a plane lamina is written as, uxx+uyy=0 0≤x≤1,…

Q: An engine operating on the air diesel cycle with k=1.3 has thermal efficiency of 63% and a cut-off…

Q: True or False: 1. As temperature rises, mach number is greater 2. An airplane flying with mach…

A: Soln:- 1 st statement :- As temperature rises , the speed of sound is faster . But the speed of…

Q: Torque is the rotational equivalent of kinetic energy force linear momentum…

A: Correct answer: 2. force

Q: 1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes…

A: h1 is the specific enthalpy of saturated liquid water at the exit of condenser corresponding to…

Q: Yellow, Brown, Red, Silver Black, Brown, Black, Silver

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Assume a steel pipe of r, = 10 mm, exposed to natural convection at h = 50 W/m².K. This pipe is insulated by the
material of thermal conductivity k = 0.5 W/m.K. Determine the critical thickness of this combination:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.08 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are h; = 18,000 W/m²-K and ho = 12 W/m²-K. Determine the heat loss (kJ/min) from 4 m of pipe. • show conversions, units, and box in your final answers
2. A pipe with: ID: 130mm OD: 165mm k=15 W/m?-K L= 2m is insulated with several materials, and convection on the inside and outside of the pipe is as follows. Oil inside is at 118°C and air outside is at 25°C KA or h 10.256 W/m2-K Material Thickness A 25mm В 2.369 W/m2-K 30mm C 0.257 W/m2-K 40mm h=120.3T2/3 (T in K) h=0.272/3 (T in K) Oil inside Air outside Determine the heat losses of the pipe, and what must be the temperature of the oil to decrease the heat losses by 20%?
A long wire of diameter D = 2 mm is submerged in an oil bath of temperature T∞ = 23°C. The wire has an electrical resistance per unit length of Re′=0.01 Ω/m. If a current of I = 180 A flows through the wire and the convection coefficient is h = 529 W/m2 · K, what is the steady-state temperature of the wire? From the time the current is applied, how long does it take for the wire to reach a temperature that is within 2°C of the steady-state value? The properties of the wire are ρ = 2,334 kg/m3, c = 537 J/kg · K, and k = 43 W/m · K.
A thick-walled tube of stainless steel [18% Cr, 8% Ni, k=19 W/m - °C] with 2-cm inner diam- eter (ID) and 4-cm outer diameter (OD) is covered with a 3-cm layer of asbestos insulation [k =0.2 W/m - °C). If the inside wall temperature of the pipe is maintained at 600°C, calculate the heat loss per meter of length. Also calculate the tube-insulation interface temperature.
QUESTION 2 hot steam pipe (k =16 W/m K) has an inside and outside diameter of 80 mm and 190 mm. If the temperature of the steam is 523 K with h 3000 W/m² K and the outside temperature of the pipe is 353 K. If the pipe is 2 m long compelete the following the thermal resistance of heat transfer by convection is = the conductive heat resistance is the heat transfer per unit length is
plz answer this,ASAP,thx At high temperatures a nuclear reactor consists of a cylindrical wall composite as the fuel element thorium (k = 57 W/mK) wrapped in graphite (k = 3 W/mK) and helium gas flows through a circular cooling channel. Cylinder length 200 mm. Taking into account the helium temperature = 600°C and the convection coefficient, h= 200 W/m²K. When measured, the outside temperature is 100°C, and h = 5 W/m².K. Draw the electrical analogy, and calculate the overall heat transfer rate!
Please show all steps not Ai generated they have been wrong and I need to understand whats goin on. A steel sphere (AISI 1010), 100 mm in diameter, is coated with a dielectric material layer of thickness 2 mm and thermal conductivity 0.04 W/m • K. The coated sphere is initially at a uniform temperature of 500°C and is suddenly quenched in a large oil bath for which To = 100°C and h = 3000 W/m • K. Estimate the time required for the coated sphere temperature to reach 150°C. Hint: Neglect the effect of energy storage in the dielectric material, since its thermal capacitance (pcV) is small compared to that of the steel sphere.
(2) The pipeline made of steel tube with a diameter of 150x5mm, should be covered with two layers of insulation: material of A (= 0,04 W/(m-K)) and material of B (Ag= 0,1 W/(m-K)). The thickness of each layer should be the same- equal to 30 mm each. Verify that the stacking order of insulation layers on the pipe will be affect on the conduction heat transfer by a such cylindrical thermalinsulation.
Example 3.3: The temperature at the center of a tender-boiled potato needs to be 98.9°C. Let's take a potato with 4 cm diameter at 5°C and and put it in vigorously boiling water at 100 °C, where convection coefficient is 1200 W/m². c. How much time will it take to cook the potato? Potato properties: density p=1070 kg/m³, conductivity k=0.8 W/m.°c, specific heat c = 3400 J/kg-°C.
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.075 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are hi = 18,000 W/m²-K and ho 12 W/m²-K. Determine the heat loss (kJ/min) from 5 m of pipe.
Below is a diagram of a pipe with 5 m radius, temperature of 5000 K, and k = 450 W/m-K. The pipe is covered by a steel that is 1.8 m thick with k = 17 W/m-K. The temperature inside is 5000 K while the temperature outside is 800 K. TB = 800 K TA = 5000 K k = 450 W/m-K K = 15 W/m-K Answer the following: 1. Calculate the system's heat loss per unit length (W/m²). 2. Calculate the temperature between the pipe and the steel (temperature in K). 5 m 1.8 m/