7.127: Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm, are attached to a wall with surface temperature of 350°C. The fins are made of material with thermal conductivity of 240 W/m-K, and they are exposed to an ambient air condition of 25°C and the convection heat transfer coefficient is 250 W/m².K. Determine the heat transfer rate and plot the temperature variation of a single fin for the following boundary conditions: (a) Infinitely long fin (b) Adiabatic fin tip (c) Fin with tip temperature of 250°C (d) Convection from the fin tip (e) Tabulate the values for the temperature variations for parts (a) to (d) () Plot the temperature variations for parts (a) to (d) (g) Explain your plot. Solution: Write orderly & Clean. Detail solution is required: [Formula, substitutions, answers, units]

7.127: Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm, are attached to a wall with surface temperature of 350°C. The fins are made of material with thermal conductivity of 240 W/m-K, and they are exposed to an ambient air condition of 25°C and the convection heat transfer coefficient is 250 W/m².K. Determine the heat transfer rate and plot the temperature variation of a single fin for the following boundary conditions: (a) Infinitely long fin (b) Adiabatic fin tip (c) Fin with tip temperature of 250°C (d) Convection from the fin tip (e) Tabulate the values for the temperature variations for parts (a) to (d) () Plot the temperature variations for parts (a) to (d) (g) Explain your plot. Solution: Write orderly & Clean. Detail solution is required: [Formula, substitutions, answers, units]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer in 10 minutes i want the solution fast Proportionality and scaling:
Note: Round your final answer to 2 decimal places if it is not a whole number. Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.
Keep the same colors the same graph, basically keep everything the same just make the line with a small curve just as shown on the picture Keep everything the same just make the line less curvy please do not change the colors of the line and the circles do not change anything besides the curve of the line. Use this code on MATLAB and fix it. % Sample data for Diesel and Petrol cars carPosition = linspace(1, 60, 50); % Assumed positions of cars % Use the 'seed' function instead of 'rng' seed = 50; % Define your seed here rand('seed',seed); % Assumed CO2 emissions for Diesel and Petrol CO2Diesel = 25 + 5*cos(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Diesel CO2Petrol = 20 + 5*sin(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Petrol % Fit polynomial curves with a reduced degree of 2 pDiesel = polyfit(carPosition, CO2Diesel, 2); pPetrol = polyfit(carPosition, CO2Petrol, 2); % Generate points for best fit lines fitDiesel = polyval(pDiesel, carPosition);…
Please make the charts for the questions. Please refer to Successful Project Management (7th Edition). Attached is the example Thank you.
I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.
This code keeps on generating graphs with different curves. The picture that you see two different graphs comes from the same code but both of them have different curves. I need the curve to look like the picture that only has one graph. I basically need the line to have a slight curve and every time I run the code it will come up as the same graph every time. Use this code on MATLAB and fix it % Sample data for Diesel and Petrol cars carPosition = linspace(1, 60, 50); % Assumed positions of cars % Use the 'seed' function instead of 'rng' seed = 50; % Define your seed here rand('seed',seed); % Assumed CO2 emissions for Diesel and Petrol CO2Diesel = 25 + 5*cos(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Diesel CO2Petrol = 20 + 5*sin(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Petrol % Fit polynomial curves with a reduced degree of 2 pDiesel = polyfit(carPosition, CO2Diesel, 2); pPetrol = polyfit(carPosition, CO2Petrol, 2); % Generate points for best fit…
Hello I’m trying to make the graph that you see in the picture, I’m trying the exact copy of that graph using this code but I’m having a hard time doing that. Could you change the code so that it looks like the graph that you see on the picture using MATLAB, please send the code when you are finished. % Sample data for Diesel and Petrol cars carPosition = linspace(1, 60, 50); % Assumed positions of cars % Fix the random seed for reproducibility rng(45); % Assumed positions of cars CO2Diesel = 25 + 5*cos(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Diesel CO2Petrol = 20 + 5*sin(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Petrol % Fit polynomial curves pDiesel = polyfit(carPosition, CO2Diesel, 3); pPetrol = polyfit(carPosition, CO2Petrol, 3); % Generate points for best fit lines fitDiesel = polyval(pDiesel, carPosition); fitPetrol = polyval(pPetrol, carPosition); % Plotting the data figure; hold on; scatter(carPosition, CO2Diesel, 'o', 'MarkerEdgeColor', [1 0.5…
You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…
Make a working drawing of one of the parts shown in below figure Refer to the drawing for setup of views. Draw complete top and front views and a partial auxiliary view. Hidden lines may be added for clarity. Note: use creo parametric to sketch the figures
Rewrite the following sentences to better suit the engineering writing style, as described in lectures. “After averaging the results from several tests, it was determined that the most efficient tire pressure was 45 psi.” “We discovered that the rising temperature in the water tank was due to an overheating filter pump.” “The air flow speed is measured and it’s found to be 12 m/s.”
please sovle part (I) and give me the formulas used in excel Try to find a result less than 50 for the question
Hello tutors, help me. Just answer "Let Us Try"