b) A non-inverting amplifier is shown in figure Q2a : Vin R2 V. RI ov- Figure Q2a : Non-Inverting Amplifier If the non-inverting amplifier had a gain, A, so that V, = A(V*-v^) show that its non-ideal voltage gain is : i) V R+ R 1 R, 1 R, + R, 1+ A R, ii) If A was ideal then what would be the circuit's voltage gain?

b) A non-inverting amplifier is shown in figure Q2a : Vin R2 V. RI ov- Figure Q2a : Non-Inverting Amplifier If the non-inverting amplifier had a gain, A, so that V, = A(V*-v^) show that its non-ideal voltage gain is : i) V R+ R 1 R, 1 R, + R, 1+ A R, ii) If A was ideal then what would be the circuit's voltage gain?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

kindly add notes: Topic: Op-amp The op-amps shown in thecircuit on the right are ideal. Assume neither of themare operating in saturation.Determine the values of v1 and v2 if v01 = 15 V andv02 = 10 V.
the help of a b) For an op-amp circuit in Figure 2(a), prove that V, -(1+2) () (10v, +V₂) w 10R Figure 2(a) and V
For the combinational op-amp circuit, Find V01, V02, V03, and V0.
2 Figure 3 shows an operational amplifier circuit with two current sources to model its bias currents. The op-amp can be considered as ideal. ) !-10µA Vi* Rx Vo R2 I=10µA R1 Figure 3 (D) Determine the output voltage of the amplifier for Vi=0.1V, Rx=00.
In this ideal op-amp circuit, it is given: va = 0.19 volts, vb = -0.45 volts, R₁ = 6 ohms, R2 = 17 ohms, R3 = 7 ohms, R4 = 13 ohms, and R5 = 3 ohms. What is the value of Vout (in volts) ? Va Vb o R₁ M R5 R₂ M + R3 M R₁ M + - Vout
Q3) For the OP Amp show in figure calculate the O/P voltage when the I/P voltage is 2V and current through 25K2 resistor 25 k2 10 k2 iz5 V- +, V*
Application of Op-Amp
For the op-amp circuit shown below, if Vin=2.5 V, R1= 7 kn, and R2=13 ko, determine the value of the output voltage. R2 R, 12 Vin Vout a. -2.38 V O b. 4.64 V O c. 2.38 V O d. -4.64 V O e. -3.71 V O f. -2.97 V O g. 2.97 V h. 3.71 V
In the circuit below, the operational amplifier is ideal with the output voltage limitations V*=12V and V-=-12V. D is an ideal diode. a) Derive the symbolic expression for Vo in terms of Vi. You should clearly show every step in your answer. b) For R₁ = 12 kn, RF = 3 kQ, R₁ = 5 KQ and with the V₁ = 8-sin(wt) input voltage signal, calculate Vo and draw Vo voltage waveform with respect to Vi specifying the important values on the axes on the plot(s). Every numerical value on the plot(s) should be explained in detail on your answer sheet. c) What is the function of this circuit? Considering its function, what is the most important drawback (if any) of this circuit? Explain your answer. Vi Ri RF D Vo RL
it's urgent please solve asap
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 3.6 V, V2 = 4.7 V, R1 = 37 kQ, R2 = 62 KQ, R3 = 77 kQ, R4 = 71 kQ, and R5 = 90 kQ. R1 ww V1 + R2 V2 R3 R4 R5 mm D
Electrical Engineering - elctronic ll Please solve the question quickly