4and5part please RfRI* VoRLVIFigure IIn the Figurel, let R1 = 4kN, Rf =12KQ, and V1 = 2V. The load resistance RL ofSk2 is connected at the output. Calculate the following if the supply voltagesrange between +12 V to -12 V.i) Voii) Acı (Closed Loop gain)iii) The load current Iiv) The output current lo indicating proper direction of flow.v) The maximum value of the ratio of feedback resistance to resistance R1possible for the circuit with the voltages as mentioned.

Answered: Image /qna-images/answer/1b99e2da-06e0-4e47-a0e2-f5fc95647482.jpg

RI Vo RL VI Figure 1 In the Figurel, let RI = 4kN, Rf =12k2, and V1 = 2V. The load resistance RL of Ska is connected at the output. Calculate the following if the supply voltages range between +12 V to -12 V. ) Vo ii) AcL (Closed Loop gain) ii) The load current I iv) The output current lo indicating proper direction of flow. v) The maximum value of the ratio of feedback resistance to resistance RI possible for the circuit with the voltages as mentioned.

RI Vo RL VI Figure 1 In the Figurel, let RI = 4kN, Rf =12k2, and V1 = 2V. The load resistance RL of Ska is connected at the output. Calculate the following if the supply voltages range between +12 V to -12 V. ) Vo ii) AcL (Closed Loop gain) ii) The load current I iv) The output current lo indicating proper direction of flow. v) The maximum value of the ratio of feedback resistance to resistance RI possible for the circuit with the voltages as mentioned.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the block diagram of the demodulation process Of DSB-SC :- 1-Nonlinear Modulator 2-Switch Modulator (Ring Modulator & Diode-Bridge Modulator)
An oscillator employs .................. feedback 1. Positive 2. Negative 3. Neither positive nor negative 4. Data insufficient
1-C) Which op-amp IC is more suited for digital applications, and why?1-D) Which op-amp IC is more suited for instrumentation applications, and why?
13. Draw a 4-bit switch Digital-to- Analog Converter (DAC).
Answer the following questions about Digital to Analog Converter (DAC): 1. Write its definition. 2. Draw its block diagram.
An oscillator employs .................. feedback 1. Positive 2. Negative 3. Neither positive nor negative 4. Data insufficient
answer number 1 only
Q1: a) Design the oscillator in Figure 1 to start oscillation with R closed-loop gain of 8.5, then sustain oscillation at a resonant R1 o Vout frequency Assuming of 3.4 kHz. the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback R2 C2 resistance setting when R3 R4 C3 oscillation is stable? 1.0 kN Figure1
I hope the solution is clear and understandable
(Boost de-dc converter with continuous inductor current. Evaluation of inductor and capacitor values) EX3: The boost converter shown bellow has the following specifications: Vin = de input voltage = 12 V, de output voltage = 30 V, output voltage peak-to-peak ripple = 1% Inductor current peak-to-peak ripple 10%, f;= switching frequency = 25 kHz and R = load resistance = 50 N Assuming that the converter is ideal, calculate: a) The duty cycle. b) The average input current. c) The minimum required inductance that ensures continuous inductor current. d) The required inductance so that peak-to-peak current ripple = 10%. e) The minimum and maximum values of the input current. f) The value of the output capacitor so that the output voltage ripple = 1%. g) Verify the theoretical results with the respective simulation ones. Boost inductor Output filter capacitor D VL 1R Vin S R Vo