At t=0, temperature of water suddenly changed from 25°C to 100°C. The transfer function of the sensor is given as V=(0.06V/°C) (T- 20°C). The output voltage was measured every 0.1s and recorded in Table 1. Find the equation explaining the dynamic behaviour of the sensor. Table 1 Time (sec) 0.0 0.1 0.2 0.3 0.4 0.5 Voltage (V) 0.3 1.8 2.8 3.4 3.9 4.2

At t=0, temperature of water suddenly changed from 25°C to 100°C. The transfer function of the sensor is given as V=(0.06V/°C) (T- 20°C). The output voltage was measured every 0.1s and recorded in Table 1. Find the equation explaining the dynamic behaviour of the sensor. Table 1 Time (sec) 0.0 0.1 0.2 0.3 0.4 0.5 Voltage (V) 0.3 1.8 2.8 3.4 3.9 4.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the system shown in Figure 2, u (t) and y (t) denote the absolute displacements of Building A and Building B, respectively. The two buildings are connected using a linear viscous damper with damping coefficient c. Due to construction activity, the floor mass of Building B was estimated that vibrates with harmonic displacement that is described by the following function: y(t) = y,cos (wt). k/2 Building A H k/2 M(t) C 73(1) Building B Equivalent (Building A) 00000000 Figure 2: Single-degree-of-freedom system in Problem 2. 111 uft) Please compute the following related to Building A: (a) Derive the equation of motion of the mass m. (b) Find the expression of the amplitude of the steady-state displacement of the mass m. (1) (Building B)
The position with time of an object is given byx(t)=Acos(ωt) If the amplitude is 1.58 m, and the frequency is 1.2 Hz, what is the object's acceleration at 11.26 seconds?
r:09 moodle1.du.edu.om An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 c. 0.2356 and 0.5625 d. 0.5215 and 0.5625 Previous page Next page 1 Assignmen II
The system y(t)=x(t)cos[2(pi)t] is linear time invariant nonlinear time invariant O linear time variant O nonlinear time variant
QUESTION 2 Vibration absorber (also called tuned mass damper) is used to reduce* the vibration at the natural frequency of the original system. Consider a M-K system shown below. Original System x(t) Modified System x₁(1) X2(t) K M F(t) K M m F(t) absorber K This system has a natural frequency at rad. The absorber mass and the spring are attached to the original system as shown in the figure, and the values are selected so that (1) the amplitude of the original mass, M, at M the original natural frequency is zero, and (2) the new natural frequencies are moved away from the original natural frequency. The selection of absorber mass and stiffness, m and k, is easy. They have the same ratio as the ratio of the original system. That is, M/m = KIK. Find the transfer functions X1(s)/F(s) and X2(s)/F(s) before you can answer questions. * I said "reduce," but for undamped system, it can be completely eliminated. What is the response amplitude (particular solution only) of the second mass if…
Drive the 3 equations mentioned above?How??
Subject: Mechanical Measurements Do not copy online solutions. It's different value
QUESTION 1 Solve the following differential equation in Matlab using ode45.m. Use time interval of 0.1 second. (Don't use options in ode45 to change teh tolerance.) d²x (1) +x(t) dx(1) dt +x(t)=0 dx x(0) = 0, =1. dt =0 What is x(t=0.8)? 0.653 ○ 0.726 ○ 0.498 0.547 ○ 0.651 ○ 0.895
5. For a slab with thickness 2 cm, the temperature is maintained at To and T₁ at x = 0 and x = L. When To 40 °C and T₂ 60 °C, a heat flux sensor measures the magnitude of the heat flux as 40 W/m². Assume that the thermal conductivity k is a linear function of temperature. a) If, when To -40 °C and T₁ = 80 °C, the same heat flux sensor measures the magnitude of the heat flux as 80 W/m², what is the temperature dependence of k? b) If, when To -40 °C and T₂ = 80 °C, the same heat flux sensor measures the magnitude of the heat flux as 100 W/m², what is the temperature dependence of k? c) If, when To=40 °C and T₂ = 80 °C, the same heat flux sensor measures the magnitude of the heat flux as 60 W/m², what is the temperature dependence of k? =
a) A rotary incremental encoder is used to measure the rotational speed of a shaft. The encoder disk is connected to the shaft directly and the sensor signal is fed into a frequency counter. The frequency counter is able to measure a frequency from 0 to 16kHz with the accuracy of 0.5Hz and the maximum speed of the shaft is 10000 rpm. i. Determine the required number of slots of the encoder disk in order to measure the maximum range of the shaft speed. What is the smallest change of speed detectable by the encoder and frequencv counter system as proposed in c(i) ? ii. iii. What are the advantages and disadvantages of increasing the nurnver or siots o be higher than that of c(i) ? What are the advantages and disadvantages of decreasing the nuniuei ui Siots to iv. be lower than that of c(i) ? b) Describe and briefly explain the advantages of instrumentation amplimiers over differentiai amplifiers and the areas of applications of instrumentation amplifiers. c) An LVDT with primary voltage…
Problem 4-1: During a step function calibration, a first-order instrument is exposed to a step change of 100 units. If after 1.2 s the instrument indicates 80 units, estimate the instrument time constant. Estimate the error in the indicated value after 1.5 s. For this instrument, y (0) = 0 units; K = 1 unit/unit.
b24 Find the rms value for the following waveform over one full cycle. 40(V) -1 cycle - 16 7 8 9 10 11 12 (S) -1