AT section show in the fig. is subjected to a shear force F. Find the value of shear force F if max. shear stress developed is 5N/mm2. 12 mm 120 mm- 12 mm 120 mm

Q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm- diameter…

A: Given Data Diameter of rod (d1) = (d2) = (d3) = 15mm  E1 = E2 = E3 = 200 GPa Determine the…

Q: Determine the shear strain Yxy at corners D and the plastic distorts as shown by the dashed lines. 3…

A:

Q: Question A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given : thickness of plate= 12mm  connect to 8mm thick plate  2×8>12  hence  t= 12mm Dia of rivet…

Q: Which stress element below correctly shows the normal and stress at point X? M T A G B D H Write the…

A:

Q: Activity A B C D E F G H 1 J K Depends on Completion of Activity A B с B D and G B I and F

A: The activity on arrow (AoA) technique is a project management tool for mapping and scheduling…

Q: maximum value for the load R.

A:

Q: In the figure shown, determine the normal stresses at AD • and BC • shearing stress at bolt D • ,…

A: Calculation: The moment at point C can be calculated as, ∑MC=0200.25+0.4-RD0.4=013-RD0.4=0RD=32.5 kN…

Q: If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below

A: DETERMINATION OF MAXIMUM TENSILE STRESS IN THE BEAM

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: B. There are 5 Materials needed to test for its strength Capacity. the stress of the materials are…

A:

Q: 16 mm B 3 mm 3 mm 16 mm 16 mm- -16 mm-

A: Draw the figure.

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A:

Q: Determine the stress of the compression steel. 200 60 20mm 450 32mm 60 A 95.64 B 40.78 4.78 90.858

A:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the…

A: Determine the magnitude of the force P for which the tensile stress in rod AB has the same magnitude…

Q: The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point…

A:

Q: The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the…

A:

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

A:

Q: For the sets of given stresses on an element given in Table below, draw a complete Mohr's circle,…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Three round bars welded together axially loaded as shown. Find the normal are stress in each bar if…

A: Stress is defined as the force acting per unit area of a bar. The stress in a bar is directly…

Q: normal stress = o = omax = For 8kN maximum stress is, 8×0.2 1 -×0.8×0.4² 12 MxCx Ix omax = AM = MyCx…

A:

Q: Part A The stress at a point is shown on the element. Suppose that a = 105 MPa, T,, = 158 MPa .…

A: step 1-

Q: -0/02 -400 m

A:

Q: A beam is supported as shown, and its cross-section is rectangular with a=5 cm and w= 2 cm. What is…

A: Solution Given Data a= 5 cm w= 2 cm

Q: arning Goal: me member shown is subjected to a compressive ress in the x direction of a = 400 ksi…

A:

Q: 2. A cantilever beam of 1.0 m long is subjected to a concentrated load Po at its free end. Determine…

A: given: allowable  tensile stress=180MPa allowable compressive stress=140MPa allowable shear…

Q: Q) The rectangular plate shown in the figure below with dimensions h=20 mm and b=50 mm changes shape…

A: Given h=20mm b=50mm Δb=0.12 mm Δh=0.03 mm

Q: Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if…

A:

Q: Q1: make introduction relating to all topics? 1. Shear force and bending moment on skateboard 2.…

A: Introduction 1. shear force and bending moment on skate board : When constructing a building, it's…

Q: 2.10 The stress tensor at a given point 0 in a loaded component relative to the x-, y-, and z-axes…

A:

Q: An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross…

A:

Q: has a yield strength of 45 ksi. What maximum contact stress will result from the load ofF = 2600 lb?…

A: Contact stress: - It is defined as a stress which develops when two surfaces come in contact with…

Q: 3 ksi S ksi iven the state of stress above (ignore 70° plane): calculate the maximum she ress,…

A: To find maximum shear and principal stress

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A: Force will be minimum of shear strength of bolts and axial strength of Plate

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

A: Introduction : The question is related with solid mechanics . In this question the data of tensile…

Q: Determine the absolute maximum shear stress developed in the beam Express your answer to three…

A: Given : Rectangular cross-section  b = 3 in d = 6 in For the given loading in the beam, maximum…

Q: Athin rectangular plate is uniformly deformed as shown. If L₁ = 0.125 in. and L₂ = 0.135 in.,…

A:

Q: The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point…

A: Given data- Shear stress at point P=12 MPa, I-section is shown. To Find- The stress at point Q.

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.