At room temperature (200C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 1400C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod. (c) If the temperature is allowed to go up continuously, which rod would fail first? At what temperature would failure occur? Given the ultimate stress (in compression) for steel is 500 MPa for steel and 350 MPa for aluminum (Typo in figure: Coefficient of thermal expansion for aluminum is 23 x 10-6/0C). 0.5 mm 300 mm - 250 mm B Aluminum Stainless steel A = 2000 mm E = 75 GPa a = 23 × 16-°C A = S00 mm E = 190 GPa a = 17.3 x 10-6/°C

At room temperature (200C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 1400C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod. (c) If the temperature is allowed to go up continuously, which rod would fail first? At what temperature would failure occur? Given the ultimate stress (in compression) for steel is 500 MPa for steel and 350 MPa for aluminum (Typo in figure: Coefficient of thermal expansion for aluminum is 23 x 10-6/0C). 0.5 mm 300 mm - 250 mm B Aluminum Stainless steel A = 2000 mm E = 75 GPa a = 23 × 16-°C A = S00 mm E = 190 GPa a = 17.3 x 10-6/°C

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A gas is at 24 ∘C. To what temperature must it be raised to triple the rms speed of its molecules?
A student cramming for their final exam heats up 0.500 L of cold coffee in a Pyrex carafe. The carafe is filled to the brim with the coffee and both are initially at 20.0 celcius. Once the temperature of both the coffee and the carafe have risen to 95.0 degrees celcius, how much coffee has spilled out? Given that the carafe is an isotropic solid, and that the coefficient of linear thermal expansion for Pyrex is: 0.0000033 1/K and that the coefficient of volume thermal expansion for water (coffee) is 0.000207 1/K
The moment of inertia I of a uniform rod rotating around its center point is I = 1/12ml^2 where m is the mass of the rod and l is its length. (A) Derive an expression for the change in the moment of inertia for such a rod, ΔI, that includes the initial moment of inertia I0, the coefficient of linear expansion  for the rod material, and a temperature change ΔT. (B) A uniform rod of mass 0.500 kg and length 1.000 m at T = 0 °C rotates around its center in free fall (e.g., floating in a space station) at an angular velocity of exactly 1 radian per second. If it is warmed to 30 °C and = 20 × 10  −6 °C−1, what would its angular velocity be? Use conservation of angular momentum.
Please Asap
A Cooper telephone wire has essentially no sag between poles 68m apart on winter day when the temperature is -20C. How much longer is the wire on a summer day when the temperature is 30.0C? Coefficient of linear expansion for copper is 1.70*10^5
Consider a 55-cm-long journal bearing that is lubricated with oil whose viscosity is 0.1 kg/m?s at 20°C at the beginning of operation and 0.008 kg/m?s at the anticipated steady operating temperature of 80°C. The diameter of the shaft is 8 cm, and the average gap between the shaft and the journal is 0.08 cm. Determine the torque needed to overcome the bearing friction initially and during steady operation when the shaft is rotated at 1500 rpm.
A cylinder that has a 45.0-cm radius and is 50.0 cm deep is filled with air at 19.5°C and 1.00 atm shown in figure (a). A 21.0-kg piston is now lowered into the cylinder, compressing the air trapped inside as it takes equilibrium height h; as shown in figure (b). Finally, a 21.5-kg dog stands on the piston, further compressing the air, which remains at 19.5°C as shown in figure (c). Ah 50.0 cm h; (a) How far down (Ah) does the piston move when the dog steps onto it? mm (b) To what temperature should the gas be warmed to raise the piston and the dog back to h,? °C Additional Materials 1 eBook
A sample of 2.37 moles of an ideal diatomic gas experiences a temperature increase of 65.2 K at constant volume. Find the increase in internal energy if only translational and rotational motions are possible.
A gas is at 27 degrees celsius. To what temperature must it be raised to triple the rms speed of its molecules? I got an answer of 243 degrees celsius. What did I do wrong?
At what temperature (in C) is the rms speed of helium atoms(molar mass 4.00 g/mol) the same as the rms speed of nitrogen molecules(molar mass 28.0 g/mol) at 20.0C? (Note that helium remains agas at temperatures above -269C.)
A student foolishly attempts to stop a steel bar, of length L = 1 m and at a temperature of 20ºC, from thermally expanding by attaching it to a wooden support with a nail at each end. Steel's Young's modulus is Y = 1.1 × 1011 N/m2 and it's linear thermal expansion coefficient is α = 13 × 10-6 1/C. Randomized Variables Y = 1.1 × 1011 N/m2α = 13 × 10-6 1/C What is the volue of the stress, in pascals, that develops due to a rise of temprature to 21 C? Assuming the nails have a cross- sectional area of A= 10^-5 m^2 all of which is perpendicular to the stress force from the bar, what is the force acting on each due to that temperature rise?
The gap width is 1.610 cm when the temperature is 30.0°C. Determine the gap width when the temperature is 205°C. (Use 11 ✕ 10−6 (°C)−1 for the average coefficient of linear expansion for steel. Give your answer to at least three decimal places.)