At a temperature of 40°F, a 0.08 in. gap exists between the ends of the two bars shown. Bar (1)is an aluminum alloy [ a= 12.5 × 10°F] and bar (2) is stainless steel [a = 9.6 ×10/°F]. Thesupports at A and C are fixed. Determine the lowest temperature at which the two bars contacteach other?(1)(2)B40 in.55 in.0.08 in. gap

Given data Initial temperature of bars (Ti) = 40˚F Coefficient of thermal expansion for bar 1 &…

At a temperature of 40°F, a 0.08 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [ a= 12.5 × 10 j°F] and bar (2) is stainless steel [a = 9.6 ×10 /ºF]. The supports at A and C are fixed. Determine the lowest temperature at which the two bars contact each other? (2) 40 in. 55 in. 0.08 in. gap

At a temperature of 40°F, a 0.08 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [ a= 12.5 × 10 j°F] and bar (2) is stainless steel [a = 9.6 ×10 /ºF]. The supports at A and C are fixed. Determine the lowest temperature at which the two bars contact each other? (2) 40 in. 55 in. 0.08 in. gap

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
Q;Determine the stiffness and elasticity matrices of the system below:
Question 1: 0.5 mm At room temperature (20°C) a 0.5-mm gap exists between 300 mm 250 mm the ends of the rods shown. At a later time when the temperature has reached 140°C, Determine: a) The normal stress in the aluminum rod A b) The change in length of the aluminum rod Aluminum A = 2000 mm² E = 75 GPa Stainless steel A = 800 mm2 E = 190 GPa Solution a = 23 × 10-6ºC a = 17.3 × 10-6°C
The telephone pole AB weighing 3730 N is resting in a hole that is 2m deep. If the contact force between the pole and the edge of the hole is limited to 2500 N, what is the largest safe value of the angle 8 ? 0 12 m 2 m B
An aluminum alloy [E = 72 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 255 mm, a cross-sectional area of A = 6500 mm2, and a length of L = 4.6 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 68°C, the longitudinal normal strain in the plate is found to be 2570 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 205 mm, a wall thickness of 11 mm, and a length of 4.2 m. The pipe supports a compressive load of 615 kN. After the temperature of the pipe drops 48°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
A force of Fi = (180 i -250j + 190k) lb is applied to the pipe assembly at point B. A force of F2 -250j + 250k) lb is applied to the pipe assembly at point D. The pipe assembly is supported by a fixed support at point A. (180 ? F1 В d3 C d1 d2 y F2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 1 ft d2 2 ft dz 3.5 ft a. Determine the normal force at point C, Nc. Express as a Cartesian Vector. b. Determine the normal force at point C, Vc. Express as a Cartesian Vector. c. Determine the Torsional Moment at point C, Tc. Express as a Cartesian Vector. d. Determine the Bending Moment at point C, Bc. Express as a Cartesian Vector.
We know that to remove the nail at A from the board, we must apply a force F=148 N. which is applied with an angle B=17 degrees with respect to a horizontal axis. a=223 mm; L=0,7m. 8=48in degrees. BT F В a
Just want to understand this review example
A spherical gas-storage tank with an inside diameter of 32 ft is being constructed to store gas under an internal pressure of 174 psi. The tank will be constructed from structural steel that has a yield strength of 33 ksi. If a factor of safety of 3.0 with respect to the yield strength is required, determine the minimum wall thickness required for the spherical tank. O 1.52 in. O 0.92 in. O 1.24 in. O 1.91 in. O 1.60 in.
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 203 MPa. If the internal pressure in the vessel is 1930 kPa, determine the factor of safety with respect to the yield strength. 1.58 2.21 O 1.30 1.45 O 1.13