The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1=75 degrees F . Each rod has a diameter of 1.5 in. Take αal=13(10^-6)/∘F ,Eal=10(10^3)ksi,

Q: The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and…

A:

Q: By the equipment as shown in the figure, temperature can be measured. The bar AB and CD are made…

A: Given data: The length of the aluminium bar AB is, LAB=36 mm. The length of the titanium bar CD is,…

Q: calculate the original length, in mm, of a circular tube that experience a compression stress of 80…

A: Compression stress, σ= 80 MPaDeformation of the tube, δ= 0.684 mmE= 70000 MPa

Q: Determine the nodal displacement of the bar shown in Figure 1 using two element of equal length. The…

A:

Q: Show the zero force members on the figure (label them on the figure and list them on the side).…

A:

Q: Consider the two bars of identical material with their elastic modulus E = 10 × 106 psi as shown in…

A: This problem can be solved by using various methods developed for determining the deflection,…

Q: 8 kN C 8 kN В L 45° 45° 60° A E D

A:

Q: The force F = (-6i + 3j+ 10 k) N is applied to the block shown in (Figure 1). Figure 3 m A F B 1.5 m…

A:

Q: Determine the horizontal displacement of end point D of the steel rod shown in the figure. E=200 GPa…

A:

Q: A uniform cylindrical shaft is tested and found to have the above stresses. Find: σ′m and σ′a

A:

Q: An aluminum alloy [E = 8400 ksi] pipe with a cross-sectional area of A₁ = 4.20 in.² is connected at…

A:

Q: The block is subjected to a force V = 48 kN . What is the resulting deflection Δ?

A: Given information:d1 = 3 cmd2 = 3.7 cmd3 = 4 cmV=48 kN

Q: The state of stress at a point in an elastic body is defined by the stress components, G11 = 2000;…

A: as per our company guidelines we are supposed to answer ?️only first 3 sub-parts. Kindly repost…

Q: Problem 4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical…

A: The free-body diagram of the beam is as shown below,   Assumption: Let the length of aluminum and…

Q: The rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at…

A: The above question is based on Torsion of shafts.

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

A: Given: The structure is made up of stock (same stock for A-B-C and B-D). 5 mm thick. b mm wide.…

Q: The pin is used to connect the three links together. Due to wear, the load is distributed over the…

A:

Q: A force F of magnitude F = 53 N is applied at point B. (Figure 5 )Determine the magnitude of the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.