At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2

Q: The principal stresses at a point in a critical section of a machine component are 60MPa, 5MPa and…

A: Given data: The maximum principal stress is σmax = 60 MPa. The minimum principal stress is σmin = 5…

Q: The stress state at a point of a structure is shown in the figure below. Determine: (a) The stresses…

A: Given σx=45 MPaσy= 20 MPaζxy=50 MPa To find Stresses for element at 15o Principal stress

Q: A structural steel bar with a 25 mm x 75 mm rectangular cross section is subjected to an axial load…

A:

Q: 1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle…

A:

Q: The state of stress at a point is given by ox=-6 MPa, oy=4 MPa, and Txy=-8 MPa. The maximum tensile…

A: To find: The maximum tensile stress at the point. Given: The stress are σx=-6 MPa, σy=4 MPa and…

Q: A certain point in the mechanical part has shearing and normal stresses measured in MN/m^2 as shown…

A: Write the given data.

Q: Compute the deformation (change in length) of bronze (B) and steel (S) in the given diagram below,…

A:

Q: For the 2-Dimensional state of stress at a point represented by the following figure: (i) Determine…

A: According to our guidelines, we are supposed to answer the first three sub parts . Please repost the…

Q: On a stress element, the following stresses are acting: σ x = 5 ksi (Compression) σ y =  10 ksi…

A:

Q: Ql: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a…

A:

Q: Find the normal, tangential and the resultant stress & its inclination on a plane making an angle of…

A:

Q: erial when longitudinal strain is 0.12mm/mm and transverse strain is -0.03

A: Given data  Longitudinal strain=0.12mm/mm  Transverse strain=-0.0396mm/mm

Q: 2. Discuss briefly what are stress elements and how essential are these on the analysis of principal…

A: To discuss: What is stress element and how essential are these on the analysis of principle stress…

Q: At a point in a strained material, if two mutually perpendicular tensile stresses of 200 kg/cm² and…

A:

Q: as depicted in the figure. As

A: given:

Q: n a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} =…

A: Given:σx=20 MPaσy=80 MPaτxy=40 MPa

Q: If the principal stresses in a plane stress problem, are o1 = 100 MPa, o2 = 40 MPa, the magnitude of…

A:

Q: A body is subjected to the following stresses: og=10 MPa, oy -2 MPa, oz =3 MPa. Which of the…

A: For plane stress or 2D stress element they should two are normal stresses and one is shear stress.…

Q: Please work out c and d

A:

Q: Determine the normal and shear stresses that occur in the n-n plane of the figure. Present a diagram…

A: Explanation: To solve this problem, we need to use the stress transformation equations. The stepwise…

Q: 4. The state of stress at a point, for a body in plane stress, is shown in the figure below. If the…

A:

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: tive and compression negative. 45°

A: Draw the free body diagram for the above problem as follows.

Q: Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation…

A:

Q: Three wires are connected in parallel circuit. The assembly is subjected to a tension force P = 25…

A: This question is based on the concept of stress and deformation

Q: The state of stress at a point on a thin plate is as shown in the left side of the Figure below.…

A:

Q: b3 C Q ↑ D P= 23 KN R = 34 KN Square Bars b₁ = 57 mm 6₂ = 19mm b3 = 38mm WHAT IS THE AXAIL STRESS IN…

A:

Q: The state of plane stress at a point on the surface of a cylindrical pressure vessel is shown in…

A: A  B  C  D  E

Q: Plane Stress In the stress element given in Figure 3, WITH MOHR CIRCLE; (a) Determine the principal…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: The state of stress at a point in a structure is shown in the following figure. Determine: (a) The…

A:

Q: The young's modulus of a certain material is 20,000 Pa. If 10m of this material is compressed 10 cm…

A:

Q: The stress state at a point of a structure is shown in the figure below. Determine: (a) The stresses…

A: The value of normal and shear stress at plane oriented at 15° from x-axis in counter clockwise…

Q: At a point in a material, the principal stresses are 800 N/cm² and 300 N/cm² where both are tensile.…

A:

Q: C= 60 R= σ1 = 02 = Determine the principal stresses 1 and 2 for the stress element shown above: Ts=…

A: The principal stresses are The maximum shear stress is The principal plane is rotated by The radius…

Q: n element is subject to the stresses shown below in Figure 5 Calculate the centre and radius of the…

A: Givenσx=75MPaσy=-30MPaτxy=14MPa

Q: At a point in a stressed body, the known stresses are o, = 15 ksi (T). o, 12 ksi (T). oz = 11 ksi…

A: Given Dataσx=15ksiσy=12ksiσz=11ksiτxy=3ksiτyz=-4ksiτzx=0θ1=41°θ2=61°θ3=63.77°

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.