Assuming link 2 rotates at a constant rate of 180rpm CW determine the velocity of link 6 when link 2 makes a 150-degree angle with the ground. (measures as right hand horizontal) DRAW THE LOOPS AND SETUP THE EQUATIONS. Identify which variables are the outputs or how they relate to the outputs. Plug in all possible numbe

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution

A: Step 1: Step 2: Step 3: Step 4:

Q: Q1. Determine the angular velocity (0) and angular acceleration (0) ofLink DC of the for bar linkage…

A: given dataN=100rpmω2=2πN60=2π×10060=10.47rad/sso, AB velocityV2=ω2×AB=0.47×400=4.2m/s ***Please note…

Q: : Derive the equations of motion using Lagrange's equations. (Idisk = 2mr²) 2m 2r k m FOR THİS…

A: Given : To find: Equation of motion

Q: 7. In the pulley system shown below, the cylinder moves upward at a velocity of 6.7 ft/s as the…

A: Solution: Given Data: V=6.7 ft/s To Find: (a) Label the horizontal and vertical datum. (b) How many…

Q: om planar erse kiner lution of

A: Given: 2 degree freedom  2 - R manipulator

Q: Find the velocity and acceleration of slider F. Also find the angular acceleration of links EPD and…

A:

Q: Part 1: Velocity Analysis of a Mechanism VELOCITY DIAGRAM Construct a velocity diagram for the…

A:

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: aracceler eration

A:

Q: The instantaneous position of a four-bar linkage mechanism is shown in figure 1. The input link, AB,…

A: (a) To Draw: The velocity diagram describing this mechanism's motion. Showing magnitudes and…

Q: Please assist with this practice question 8. I don't know where to begin with this. Give details on…

A:

Q: possible numbers. Assuming link 2 rotates at a constant rate of 180 rpm CW, determine the velocity…

A:

Q: QUESTION 3 Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and…

A: input speed, N1 = 1750 rpm output speed, N2 = 725 rpm linear velocity, v = 4000 ft/min

Q: kwise direction. Find the locities by creating a velo olidWorks. Submit the file in the below…

A:

Q: find Find Rotation the make matrix manipulator Displacement final HTM from shown VECTORS. base…

A:

Q: 2. write Eom Then deter mine w. L12 L12 Ans 3K M+ 6m EK

A:

Q: DATUM 1.) In the figure shown, block B is pulled down with a velocity of 0.3 m/s. Calculate the…

A:

Q: Which of the following is the correct position vector loop equation for the linkage below? ONT +7…

A:

Q: At the instant 0= 20°, the angular speed of the r = 120 mm rod OA is wo = 13 rad/s and its angular…

A: Given data  r = 120 mm rod OA  Wo= 13 rad/s2  W AB = -6.6 rad/s h = 100 L = 264mm

Q: The two axes of an x-y positioning table are each driven by a stepping motor connected to a…

A: Given data as below:Gear ratio rg = 4:1Step angle ns = 200 pulse/revpitch p = 5 mm/revaxis range  L…

Q: d'y 2 dy 11 Find the order and degree of the differential equation dx? V - 4= 0. 3|2

A:

Q: Figure 2 with oco = 6 rad/s CCW. Find the velocity of point E on %3D BC and oAB-

A: Given: TO determine: Velocity at point E angular velocity of link AB

Q: 9. Given the two-link revolute robot arm with L₁= 8 and L₂= 6, 01-35°, 0₂-20° find points Px and Py…

A: Given that :                         L1= 8                          L2= 6                         To…

Q: The two axes of an x-y positioning table are each driven by a stepping motor connected to a…

A: The gear reduction is:The number of step angles is:The pitch of the lead screw is:/revThe axis range…

Q: AB is rotating counterclockwis on of (aAB = 0.6 rad/sec2). T ween C and B is rB/C = 1.6 cm Slider D…

A: vB = 3(0.1) = 0.3 m/saBt =  9 × 0.1 = 0.9 ms2aBn = 32 ×(0.1) = 0.9 ms2vB = vc+ Ω× rB/C + (vB/C)xyz…

Q: i) For the crank end shown in Figure Q1i in a crank slider mechanism with constant crank angular…

A: According to the information we have to find the relationship between  linear, velocity, and…

Q: Consider the second joint of a sphenical wrist manipulator with a rotary joint Designasingle…

A:

Q: Find the parametric equation of the two lines fla) and giv) from the figure bellow, then detect the…

A: The points (0, 0, 0) and (2, 6, 3) represent the line f(u) as given in the figure. The general form…

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: trajectory of the cutter centre to machine

A: Given; Trajectory of the cutter centre to machine the island   PQRS is ?Where,   Rectangular island…

Q: The link lengths and the values of 02, W2, and y for some inverted fourbar crank- slider linkages…

A:

Q: In relation to Cams, the prime circle is which of the following: Select one: a. The theoretical…

A: Prime circle is the smallest circle that can drawn from the center of the cam and tangential to the…

Q: The four-bar mechanism is driven by a crank (Link AB) which rotates clockwise at 150 rpm. For the…

A:

Q: 7. Given the two-link revolute robot arm with L₁= 12" and L2 = 8", 01= 45⁰, 02= -30°, find the end…

A: To solve this problem, we need to find the end-effector position (Px,Py) of the two-link revolver…

Q: The hammer speed is desired to be at x'= 10 m/s. Draw %3D the free hand flow diagram of the closed…

A: Given : speed -  10 m/s To find Closed loop diagram

Q: Q/ Crank, AB = 200 mm; Slotted arm, OC = 800 mm and link CD = 250 mm. B =30 °. find the velocity of…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.