Assuming a thermal unit with input output characteristics: F(P) = 1000+ 0.5P (S/h) the weekly average demand load fed from this unit is P=2000MW. The weekly heat consumption per MBtu for a fuel heat rate price: C-3$ / MBtu Select one: O a. 116000 (Mbtu/Week) O b. None of these O c. 199000 (Mbtu/Week) O d. 136000 (Mbtu/Week) e. 112000 (Mbtu/Week)

Assuming a thermal unit with input output characteristics: F(P) = 1000+ 0.5P (S/h) the weekly average demand load fed from this unit is P=2000MW. The weekly heat consumption per MBtu for a fuel heat rate price: C-3$ / MBtu Select one: O a. 116000 (Mbtu/Week) O b. None of these O c. 199000 (Mbtu/Week) O d. 136000 (Mbtu/Week) e. 112000 (Mbtu/Week)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

The input to a full-wave rectifier is 20 V AC (RMS). The load resistor is 20 ohms and rectifier losses are 4W. The ripple factor of the rectifier is: O A. 0.96 OB. 0.33 O C. 0.48 O D. None of the other choices are correct O E. 0.75
Answer all sub-parts if brief and with sufficient answer..
In a phase controlled full wave rectifier, the source voltage is 50 VRMS sinusoidal, the source frequency is 60 Hz and the load is 20 ohms. Since the delay angle in the circuit is 20 °, which of the following is the value of the RMS load voltage? a) 99.54 V b) 49.77 V c) 70.38 V d) 35.19 V e) 23.46 V
Thank you ?
need quick solution please
Solve it fast fast plz
The three phase full wave uncontrolled rectifier has a three-phase source of 444 V rms line-to-line, and the load is a 30 ohm resistance in series with a 50-mH inductance. Calculate the average load current. In this question, take 2 digits after the comma and take pi = 3,14; enter your answer into the system in terms of the desired unit only as a number.
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
A full-wave rectifier operating from a 60HZ supply develops a peak rectifier voltage of 23V. Calculate the ripple factor for the voltage across the 223µF capacitor for a load current of 76mA. RL Idc 4/3fC Vr(rms) Lütfen birini seçin: a.3.56% b.11.6% c.9.46% d.7.37% e.4.89% ίφ00ορορο)
Q. Define m00 re riachiné.. MOo DAw the State diagream of 1011 wi thout overlaPping
Could you solve the question ?
Q.35 Ans. In the circuit shown, the input V, is a sinusoidal AC voltage having an RMS value of 230 V ± 20%. The worst-case peak-inverse voltage seen across any diode is V. (Round off to 2 decimal places.) > KH A A 390.32 (385.00 to 395.00) KH A KH C= R ww