Assume the data below was collected for two different sample solutions using the same experimental procedure you carried out. Based on the two lines shown below, which solution (orange data points or blue data points) corresponds to the sample with the higher molar absorptivity? 0.9 y4.771 - 0.0728 0.7 0.6 04 0.3 02 y1414 - 0.0546 R0.99642 0.1 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 02 0.1 [Concentration, M] orange data points (lower line) O blue data points (upper line) Absorbance

Assume the data below was collected for two different sample solutions using the same experimental procedure you carried out. Based on the two lines shown below, which solution (orange data points or blue data points) corresponds to the sample with the higher molar absorptivity? 0.9 y4.771 - 0.0728 0.7 0.6 04 0.3 02 y1414 - 0.0546 R0.99642 0.1 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 02 0.1 [Concentration, M] orange data points (lower line) O blue data points (upper line) Absorbance

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter5: Distillation

Section: Chapter Questions

Problem 4Q

See similar textbooks

Similar questions

What is precipitation from homogeneous solution; what are the benefits of this method.
A K2SO4 solution is prepared by weighing out a certain amount of the pure solid reagent,dissolving it to 500.0 mL in a volumetric flask. An aliquot was taken from this solution.of 25.00 ml and diluted to 500.0 ml. An aliquot of 5.00 was taken from this new solution anddiluted to 50.00 ml. A chemical analysis of this new solution showed a 0.100%(w/v)in K+. Calculate the weight of the pure solid K2SO4 used for the preparation of the original solution.and its concentration in each volumetric flask. The answer is 2.23x10^2g
A 25.00 mL sample of an aqueous solution Y is extracted with 50.00 mL of hexane. After extraction, it was found that 94.12% of solute Y was successfully removed from the aqueous solution. Calculate: i. The distribution constant for this separation The initial concentration of Y if 1.77 mmol Y remains in aqueous solution after extraction. iii. The concentration of Y in BOTH phases after extraction
1a. Use the given table to construct a temperature-composition diagram for cyclohexane Toluene mixture. Based on the plot, what is the composition of the distillate obtained by Simple distillation 20 mole percent cyclohexene and 80 mole percent toluene? Show your Work on the plot. 1b. Estimate the composition of the distillate of 20 mole percent of cyclohexane if the Distillation column had three theoretical plates.
Hexanoic acid was added to an immiscible biphasic solvent system, water and CCl4 at 20.0OC and the equilibrium concentrations of hexanoic acid were determined to be 3.66 g/L in H2O and 67.0 g/L in CCl4. Caluclate the distrubution coeffiecent (D2) of hexanoic acid in water with respect to CCl4.
21. If the unknown well water samples were analyzed at 508 nm but the external standard solutions were analyzed at 420nm, fully explain how this would influence your mean Fe2*concentration in the unknown well water sample.
16) Which of the following(s) is/are correct? I- Selectivity factor is the amount of time a solute spends in the stationary phase relative to the time it spends in mobile phase II- The retention time for an analyte is the time interval between its injection onto a column and its appearance at the detector at the other end of the column. III- Distribution constant is the ratio of the total solute concentration in the stationary phase to that in the mobile phase. A) I, II and III B) Only II C) I and III D) II and III E) Only III for GC2
A Sodium Chloride (0.1920g) NaCI was assayed using volhard Method, using 52mL of 0.0975N AGNO3 and 12.3 mL of 0.1192Ammonium thioscyanate. Calculate the sample in %.
GRAVIMETRIC ANALYSIS The addition of dimethylglyoxime, H2C4H602N2, to a solution containing nickel(Il) ion gives rise to a precipitate: Nickel dimethylglyoxime is a bulky precipitate that is inconvenient to manipulate in amounts greater than 135 mg. The amount of nickel in a type of permanent-magnet alloy ranges between 22% and 38%. Calculate the sample size that should not be exceeded when analyzing these alloys for a nickel.
A student determined the concentration of total reducible iodine in the aqueous phase based on the average of their 'best two' determinations in Part 1 to be 0.0177 M. They also determined the concentration of I2 in the CH2Cl2 phase based on the average of their 'best two' determinations in Part 2 to be 0.0196 M. Determine what the concentration of I- in water would be based on this student's previous work. Report your final answer, in mol/L, to 3 decimal places and only include the numerical value (no units). Do not use scientific notation for this question.
2.) A 0.2185g sample of NaCl was assayed using Volhard Method with 50mL 0f 0.0998N AgNO3 and 11.9mL of 0.1350N NH4SCN. Calculate the % NaCl in the sample.
I want the answer for this question please