Assume a C program has the following amount of instructions:Instruction countInstruction #, i12331364CPI₁359Calculate the following:a. Total CPU clock cycles needed for the programb. Overall CPICPU time needed for the program assuming the clock rate is 1kHz

Introduction Clock cycle: A clock cycle, also known as a clock tick, is the basic unit of time…

Assume a C program has the following amount of instructions: Instruction #, i 1 2 3 Instruction count 13 6 4 CPli 3 5 69 9 Calculate the following: a. Total CPU clock cycles needed for the program b. Overall CPI c. CPU time needed for the program assuming the clock rate is 1kHz

Assume a C program has the following amount of instructions: Instruction #, i 1 2 3 Instruction count 13 6 4 CPli 3 5 69 9 Calculate the following: a. Total CPU clock cycles needed for the program b. Overall CPI c. CPU time needed for the program assuming the clock rate is 1kHz

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 14 A program consists of 100,000 instructions as follows: Instruction Type Integer arithmetic Data transfer Floating-point arithmetic Control transfer What is the average CPI? O 3 CPI O 2 CPI O 5 CPI O None of them O 4 CPI Instruction Count 45.000 32,000 15,000 8,000 Cycles per Instruction 3 4 8 3
Please written by computer source
Assume: CPU Clock = 1 GHz 1 OP requires 5 clock cycles (arithmetic instruction, conditional, etc.) 1 memory access requires 100 clock cycles (Read or Write) Problem size: N = 1,000,000 (1 million) There is no cost associated with the loop index variable: do not count any arithmetic instructions for initializing or incrementing the loop index value, do not count any memory accesses for accessing and using the loop index variable in your computation of a sum. Assume the loop index variable is "free of charge" There is no memory cost of accessing and updating your accumulator variable (e.g., sum += ...), but there is an arithmetic operation involved in updating the accumulator variable. Questions: 1. For algorithm #1 shown below (direct sum): • How many arithmetic instructions are required by this algorithm? • How many memory accesses are required by this algorithm? • How many clocks are required by this algorithm? • What is the CPI (cycles per instruction) required by this algorithm? •…
QUESTION 43 Using the Vole machine language reference in Appendix C in the book, what is the instruction that performs the following: JUMP to the instruction at address 88 if the contents of register 2 equals that of register 0.
what is the CPU time if the number of instructions executed by the program is 500, cycles per instruction is 5 and the clock cycle time is 200 ps ? a) 1000 secb) 50000 secc) 500000 secd) 10000 sec answer
two different processors execute same instructions, Processor one has 4Ghz clock rate and 1.5 CPI, processor two has 1.3GHz and 2.2 CPI. 1)find the processor with the highest performance expressed in instructions per second 2)if both processors execute a program in 15seconds, what is the number of cycles and instructions
Compute the time required to execute the following assembly subroutine if the CPU frequency is 5 MHZ: Delay Proc Near PUSH CX MOV CX,100 Next: LOOP Next РОР СХ RET Delay ENDP Note: The instruction: Next: LOOP Next can be written as: LOOP $
calculate the rate of MIPS by executing a program that has 600 MHz processor and 1 million instructions, also the CPI of each instruction type are 1,2,4,8 and the instructions are logical, load, branch, memory respectively where the instruction mix are given as 30%, 15%, 25% and 30%· Trace the result after execution:
A particular (fictional) CPU has the following internal units and timings (WRand RR are write/read registers,ALU does all logic and integer operations and there is a separate floatingpoint unit FPU. Timings for each unit in picoseconds are:IR 230, RR 40, WR 50, ALU 200, MEM 260, FPU 380(assume instruction read and memory access are average time for access tocache)There are 5 basic instruction types: - here are instruction sequence for eachtype, time in picoseconds and percentage of each type in a typical set of testcodes:1. LOAD : IR+RR+ALU+MEM+WR : 780, 20%2. STORE: IR+RR+ALU+MEM : 730, 10%3. LOGIC/INTEGER: IR+RR+ALU+WR : 520, 40%4. FLOATING POINT: IR+RR+FPU+WR : 700, 10%5. BRANCH: IR+RR+ALU : 270, 20%1 cycle is 780ps = .780 nanoseconds for this machine, on the assumption thatall instructions take 1 cycle (assume all memory access is in cache). Clockfrequency is 1/.780 = 1.28 GHz (rounded to 2 decimals) for an ideal CPI=1
The following are the features of an Instruction Length: Describe two design issues that affect the length or size of the instruction.