Assignment For the circuit shown below; 1) Eliminate the circuit. 2) Calculate the current of the source and current in each branch. 3) The voltage across each resistance. 4) The power consumed in each resistance. 10 ohms l2 20 ohms ww V1 V2 20 v 20 ohms b.

Assignment For the circuit shown below; 1) Eliminate the circuit. 2) Calculate the current of the source and current in each branch. 3) The voltage across each resistance. 4) The power consumed in each resistance. 10 ohms l2 20 ohms ww V1 V2 20 v 20 ohms b.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Already got part 1 only answer part 2
Please help me solve questions 1-5 using the given values found.
A resistor has a resistance of 20 ohms at 30 degrees Celsius and 32 ohms at 90 degrees Celsius. Find its resistance at 125 degrees Celsius. Determine also the temperature coefficient at 100 degrees Celsius. (Please Show Complete solution and write properly) (Round off the final answer to the 4th decimal if possible and box the final answer)
Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell
Needs Complete typed solution with 100 % accuracy.
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
Determine the nodes/junctions, Current (I), Loops, Voltage drop on each Resistor (R), and Power (P) on each Resistor (R) with the following given and illustration: Use the following given for batteries and resistors (color bands for your value of resistors, use the lower limit). R1 = red red black goldR2 = orange green black silverR3 = white orange black goldR4 = green violet brown goldR5 = violet red black silverR6 = yellow green black silverR7 = brown black black gold V1 (lower left) = 100VV2 (top center) = 150VV3 (lower right) = 200V
Make three plots using Excel: 1. Voltage vs current for the linear resistor data (voltage on vertical axis, current on horizontal). Add a linear trendline with the equation and R² value shown. 2. Voltage vs current for the lightbulb data (voltage on vertical axis, current on horizontal). 3. A plot showing both curves on the same set of axes (voltage on vertical axis, current on horizontal).
Q1.) a) PMMC meter has (10mA) half scale current deflection and (1500) internal resistance. Use this meter to design a dc multimeter of indirect ammeter and direct voltmeter methods to measure the following ranges of current and voltage: 50mA, 100mA, 1A, 5V, 50V, and 150V. Draw the circuit diagram of this multimeter with a control switch that can be used to measure either current or voltage.
14. Which of the following lead-acid battery voltages has the highest value?A. Equalize voltageB. Open-circuit voltagels.C. Discharge voltageD. Floating voltage Obs: I inform you that the answer to letter " A " is wrong, according to the test I did. I appreciate your help which of this question is the correct answer. thanks
* 811 1:00 docs.google.com/forms 4 i) Figure below show an electronic device, it is O A DC voltage source A variable resistor. A switch. An Integrated circuit (1.C). ii) The resistor shown has a resistance measured in Ohms, it is equal to with a percentage of error is Second First Digit Multiplier Digit Tolerance 25, 5% 200, 10 %. 200, 5% O 25, 10%. iii) The circuit shown has an; .Ammeter, voltmeter, two resistances and variable resistor components. Describe the connection of each component (series or parallel). 0.15 A ... O O O
State the characteristics of voltage and current in a series circuit connection of resistors. State the characteristics of voltage and current in a parallel circuit connection of resistors. please explain it properly.