Assignment 1: Killer Robot Summary of the case: Bart Matthews, a robot operator at Cybernetics, Inc., has been killed by an out- of-control robot named Robbie. The creator of the robot, Silicon Technologies, is also in a tight financial position and had hoped that the robot would put the company back on its feet. It has been determined that several situations contributed to the death of Matthews: 1. Improper methodology was used in developing the software. 2. Testing of the software was faked. 3. The company pressured Robbie's creators to by-pass testing. 4. Part of the software used in the robot was stolen from another vendor's application. 5. The programmer did not understand or know the code which he used. 6. Security measures used were illegal, and therefore all information gathered in regard to the case might not be permissible in court. 7. The project leader did not understand or use proper design methodologies. 8. The end-user interface was designed improperly.

Assignment 1: Killer Robot Summary of the case: Bart Matthews, a robot operator at Cybernetics, Inc., has been killed by an out- of-control robot named Robbie. The creator of the robot, Silicon Technologies, is also in a tight financial position and had hoped that the robot would put the company back on its feet. It has been determined that several situations contributed to the death of Matthews: 1. Improper methodology was used in developing the software. 2. Testing of the software was faked. 3. The company pressured Robbie's creators to by-pass testing. 4. Part of the software used in the robot was stolen from another vendor's application. 5. The programmer did not understand or know the code which he used. 6. Security measures used were illegal, and therefore all information gathered in regard to the case might not be permissible in court. 7. The project leader did not understand or use proper design methodologies. 8. The end-user interface was designed improperly.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A. A student establishes the time constant of a temperature sensor by first holding it immersed in hot water and then suddenly removing it and holding it immersed in cold water. Several other students perform the same test with similar sensors. Overall, their results are inconsistent, with estimated time constants differing by as much as a factor of 1.2. Offer suggestions about why this might happen. Hint: Try this yourself and think about control of test conditions. B. Which would you expect to be better suited to measure a time-dependent temperature, a thermal sensor (e.g., a thermocouple) having a small diameter spherical bead or one having a large diameter spherical bead? Why?
DEPARTMENT OF MECHANICAL ENGINEERINGMENG 303 PRINCIPLES OF COMPUTER AIDED ENGINEERING Failure mode and effect analysis for Autonomous underwater vehicles, based on any standard. plese dont late
Pressurized eyes Our eyes need a certain amount of internal pressure in order to work properly, with the normal range being between 10 and 20 mm of mercury. The pressure is determined by a balance between the fluid entering and leaving the eye. If the pressure is above the normal level, damage may occur to the optic nerve where it leaves the eye, leading to a loss of the visual field termed glaucoma. Measurement of the pressure within the eye can be done by several different noninvasive types of instruments, all of which measure the slight deformation of the eyeball when a force is put on it. Some methods use a physical probe that makes contact with the front of the eye, applies a known force, and measures the deformation. One non-contact method uses a calibrated “puff” of air that is blown against the eye. The stagnation pressure resulting from the air blowing against the eyeball causes a slight deformation, the magnitude of which is correlated with the pressure within the eyeball.…
Mark the good definition
1. Please help me solve this mech. engineering question
With reference to the introductory first week's lecture for this module and the diagram titled 'Manufacturing Systems' answer true or false to the following: Manufacturing systems in a factory are all encompassing for the efficient management of the operations including the supply chain of materials, maintaining product quality and managing the loading of factory resources. True False
2 Help me answer the question
Lusaka Engineering Company (LEC) had actual quality costs for the year ended December 31, 2022, as given below: Cost Element Amount ($) Prototype verification 300,000 Process acceptance 315,000 Product liability 618,750 Recalls 243,750 Retesting 187,500 Rework 375,000 Test labour 360,000 Vendor certification 600,000 At the zero-defect state, LEC expects to spend $375,000 on Prototype verification, $75,000 on Vendor certification, and $50,000 on Process acceptance. Assume sales to be $25,000,000. Required: (a) Prepare a Cost of Quality report for 2022 using the PAF Model. What does this report tell the management of LEC? (b) Prepare a Cost of Quality report for the Zero-Defect State using the PAF Model. Explain why quality costs still are present for the zero-defect state. (c) What if LEC achieves the zero-defect state reflected in the report in part (b), what are some of the implications of this achievement?
Q1:What is different between Finite element analysis and finite element methods? Q2: What is CEA?
What does the term "tolerance" refer to when designing dynamic surfaces? A. Material durability B. The space between connected parts, designed for supported materials C. The friction and resistance between connected parts D. The dynamic surface design complexity Which of the following parameters must be considered before the design phase of a dynamic surface? Select all correct answers. A. Tolerance B. Element size C. Friction D. Minimum thickness E. Support material removal F. Positioning A dynamic surface is an array of connected surfaces that produces a mechanical effect; the movement of one surface causes predictable movement of the others. A. True B. False Which of the following are basic elements of 2D nesting? Select all correct answers. A. Part orientation B. Part combinations C. Spacing between parts D. Material selection Which of the following are benefits of proper nesting and positioning? Select all correct answers. A. Reduced material waste B. Reduced energy usage due to…
Group Technology method groups parts or products with similar characteristics into families and sets aside groups of machines for their production Select one: True False
SmartPAK (Smart Backpack) Description: The SmartPak, a cutting-edge smart backpack, is constructed using high-quality materials such as ballistic fabric, nylon fabric, polyester fabric, and polyurethane foam. These materials are carefully chosen to ensure durability and comfort for the users. Additionally, the SmartPak features water-resistant layers that protect its contents in case of rain or accidents. The SmartPak is designed with several space-saving features and valuable functionality. It incorporates multiple pockets and a spacious main compartment, providing ample storage space for personal belongings. The size and dimensions of the SmartPak vary to accommodate different torso lengths and hip widths. It is available in three sizes: small (42 cm x 64 cm), medium (46 cm x 72 cm), and large (50 cm x 98 cm). To enhance user comfort, the SmartPak is equipped with adjustable cushioned shoulder straps and a padded back panel. These features ensure a comfortable fit and reduce strain…