eaner units. After delivery, the hote mits should have been tested to mee m IEC 60312, a European standard, lics.

Q: Name 3 ways to maintain fatigue-prone components

A: In mechanical components, the fatigue failure occured when components are subjected to variable…

Q: explain the main benefit of a heat-recovery VRFsystem

A: VRF systems are also known as variable refrigerant flow. There are different kinds of VRF systems;…

Q: Write the advantages and disadvantages of gus turbime

A: (i) It is simpler in design since there are no boilers, no condensers, feed water supply, no cooling…

Q: According to the OSHA Hazard Communication Standard, seven types of hazard identification ar…

A: When chemicals are used in the workplaces there must be safety ensure in case of any hazard. In…

Q: How does a pressure control solenoid regulate transmission pressures? (50 - 80 words)

A: This question is based on the concept of pressure control solenoid.

Q: ##What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure…

A: hello Dear ):-Can update the question again . It is not show properly .thanks ):-Explanation:

Q: ons: In what situations would a circuit with multiple system pressu Are there any disadvantages to a…

A: 3. Hydraulic pressure is expressed as a force per unit of area, such as bar (kg/cm2) or PSI…

Q: Explain the features of port and direct injectors and the different testing methods without removing…

A: Port injectors and direct injectors are two types of fuel injectors used in internal combustion…

Q: Describe the PRESSURE MEASUREMENT DEVICES?

A: Pressure measuring devices are used to measure the pressure in a different manner. Based on its…

Q: List 3 objectives of reliability

A: Reliability: It is the ability of any object or system to work accurately under standard conditions…

Q: What do you think is the most important innovation in the design of Aptera?

A: The original Aptera Motors' design was a three-wheeled two-seat vehicle named the Aptera 2 Series.…

Q: describe the operatoin of a digital   EGR valve

A: Digital Exhaust Gas Recirculation (EGR)valve :-The EGR system works by returning a small portion of…

Q: what is the standard length and diamater of a drinking straw

A: The standard length and width of single-use disposable straws that you'll find at most bars and…

Q: What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing…

A: can outline a general arrangement for the piping system:PSA GEN (Pressure Swing Adsorption Oxygen…

Q: what happens when w/wn > than sqrt(2)? what happens to the damping and why did it switch, like the…

A:

Q: Wi Wz _F STEM PART 1 TAB TAB STEM TAB TAB PART2 BY NC SA 2014 Michael Swanbom Dimensions: WĄ W2 W3…

A: Stress is the ratio of force and area.

Q: How mary MI4 10.9 bolts used in Vith &s Systen ?

A: ANSWER- 5 BOLTS

Q: A company is reviewing its policy of putting each sub-assembly bought in from outside through a…

A: Find out:Advise the firm on what to do. ( inspect or not)Givencost of inspecting the sub-assembly =…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.