Aside from added strength, cite at least 3 most practical reasons for adding compression steel reinforcements in beams|

Q: 2. Find the area of a triangle whose two adjacent sides are 16 cm and 12 cm and their included angle…

A:

Q: nswer all the questions

A:

Q: Given: the IDF-curve shown in the Figure below, answer the following questions: a) Intensity for…

A:

Q: P Answers: P = FB = i i 35 kg B N N A

A:

Q: Answer

A:

Q: QUESTION 1 Determine the maximum moment in the cantilevered beam shown below, if A = 448 lb, B = 284…

A: Given Data  Find maximum moment in beam.

Q: Kindly answer all questions

A: given data: σX=7 MPaσY=-5 MPaζxy=-8 Mpa

Q: Q.15 A concrete pedestal is made of M25 concrete as shown below. The value of tana for this case is…

A:

Q: Situation 1) A closed loop of differential levels was run to establish the elevations of several…

A: given - data of differential levelling.  to find - difference of elevation between BM-6 and BM-4.

Q: Kitchen Bathroom Living Room Dining Room Library Entry Above is the floor plan for a new house. The…

A: The given floor plan is labeled which is shown below: Given scale: 1 inch: 8 feet

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: G. Suppose that the specimen of material A is unloaded before the yield strength point. For this…

A:

Q: Problem IlI. A beam shown in Figure 1 is subjected to loads as shown. 59 kN 38 kN/m B 120 kN.m 68 kN…

A:

Q: Determine the force required to hold the cone in position as shown if the cone has a weight of 200…

A:

Q: In the given project, the expected markup is 30%, four payments are expected to be paid to the…

A: Plot the given data:

Q: give me all three answers otherwise leave it.. Remember give me all answers. Thank you

A: The binder from the separated mix was extracted and recovered using AASHTO T319. The amount of…

Q: PROBLEM 1 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment…

A:

Q: What is a batter board? Boards set across a trench or otherwise placed so as to carry wire or cord…

A: Construction stakeout is the placing of a stake to indicate the location for a pole. Poles must be…

Q: player releases the horseshoe at A with an initial spe ngle 0 for which the shoe will strike the…

A:

Q: Determine the force in members CE, CF and BF for the truss loaded as shown. Ans. BF = 0.289P (T) B…

A:

Q: the DO meter showed a concentration of 8.8 mg/L. m RPD of 9% what is the saturation concentration c

A: Given:- concentration=8.8mg/L Maximum RPD=9% To find:- saturation concentration

Q: Excess or deficiency can only be prorated between found original monuments (or best available…

A: Excess or deficiency can only be prorated between found original monuments (or best available…

Q: Determine the elongation of member X of the compound truss [see figure 15], assuming it is made up…

A: Given:- A=100 sq.mm To find:- The elongation of member X

Q: In the figure P30.5, identify the reactions. Show your diagrams. 20, KN 20, KN 20 KN 5. m A 15KN 12…

A: Given- A simple truss is given To find- support reactions

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

A:

Q: A headlight is located 0.6 meter above the PVC. The light beam directs 1 degrees above the…

A: In highway driving, stopping sight distance is defined as the minimum sight distance available at…

Q: A vertical, cylindrical tank, 6 ft in diameter and 12 ft high, is held together by means of two…

A: Given : Diameter of the cylindrical tank, D = 6 ft = 1.8288 m Height of the cylindrical tank, H = 12…

Q: Given the Elevations and HI readings, obtain the values for BS and FS. Show your solution. BS HI FS…

A:

Q: construct the bar force or ettered bars. 6 at 25 ft 150 ft %3D

A:

Q: Problem 3 (MO12) (60 points) Fill up the missing data BEARINGS AZIMUTH LINE DISTANCE(m) FORWARD…

A:

Q: Kindly answer d, e, f, and g only.

A: Diameter of wooden-stave = 3.5 ft Height of the barrel = 5 ft T1 and T2 be the tensile forces in top…

Q: PLACE YOUR ANSWERS HERE. I x,0 = 10 " %3D P x,0 = 4"X6"X " r y,o = 12" 4"X 8"X 1" 1" 12 "

A:

Q: 3.1 A 520-ft-long equal-tangent crest vertical curve connects tangents that intersect at station 340…

A:

Q: The performance of a hydraulic structure during a flood has been investigated in a 36 model based on…

A: Given- Model ratio- Lr=1/36 Time Tm=3 hrs,

Q: Gate 16 in. 12 in. turpentine (54.2 pef) (a) Determine the magnitude (in Ibs) and direction (R or L)…

A:

Q: 1. What is the unit weight of aggregate? 2. How do you calculate void content of aggregate? 3. What…

A: 1.The weight or mass of an aggregate needed to fill a container with a given unit volume is its unit…

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.