As shown in the figure below, a closed, rigid tank fitted with a fine-wire electric resistor is filled with Refrigerant 22, initially at -10°C, a quality of 80%, and a volume of 0.01 m³. A 12-volt battery provides a 5-amp current to the resistor for 6 minutes. Refrigerant 22 T₁=-10°C x₁ = 80% V=0.01 m³ Resistor 12-volt battery provides a 5-amp current. If the final temperature of the refrigerant is 50°C, determine the heat transfer, in kJ, from the refrigerant to its surroundings.

As shown in the figure below, a closed, rigid tank fitted with a fine-wire electric resistor is filled with Refrigerant 22, initially at -10°C, a quality of 80%, and a volume of 0.01 m³. A 12-volt battery provides a 5-amp current to the resistor for 6 minutes. Refrigerant 22 T₁=-10°C x₁ = 80% V=0.01 m³ Resistor 12-volt battery provides a 5-amp current. If the final temperature of the refrigerant is 50°C, determine the heat transfer, in kJ, from the refrigerant to its surroundings.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0.06m of fluid at 0.6bar is compressed in a polytropic process to a pressure of 3.5bar. The fluid is then heated reversibly at constant volume until the pressure is 3bar, the specific volume is 0.4m/kg. A reversible expansion according to a law pv=c restores the fluid to its initial state. Calculate the net work done on or by the system (in kJ). 01:
Helium expands polytropically through a gas turbine according to the process PV^1.327=C. If the turbine produces 30.46 MW, determine the heat transferred in kJ/s.
5. A fluid system undergoes a non-flow frictionless process from 4.5 ft3 to a final volume 1.5 ft3 in accordance with the defining relation P= 60/V + 30 psi, where volume in ftº. During the process the system reject 30 BTU of heat. Determine the change in enthalpy and internal energy.
Mechanical Engineering A steam turbine receives hot & pressurized steam from the inlet (port 1 in the figure), produces work, and discharges steam at low pressure and temperature to the outlet (port 2). P1 = 1.5 x (modifier) MPa, T1 = 350 x (modifier) °C. P2 and T2 are given in the figure. The turbine is at a steady state. Kinetic energy and gravitational potential energy of the steam are negligible compared to its thermal energy. q is negligible Turbine w? P1= T = im =16 kg/s 2+ P, = 0.2 Mpa | T, = 150°C (a) Mass flow rate at the inlet is 10 kg/s. Compute the mass flow rate at the outlet. Show your reasoning (b) Determine the change of specific enthalpy of the steam between the inlet and the outlet. You can assume the specific heat of steam remains essentially constant during the process, with C, = 1.9 kJ/kg.K (c) Compute the work produced by the steam turbine, per unit mass of steam. (d) Compute the power production from the turbine. Power is the work produced per time, and its most…
One kilogram of an ideal gas at 5.5 bar with an initial volume of 0.3 m3 expands to a final volume of 0.5 m3 in accordance with the equation pV1.3 = C. Find the work done and the heat transfer during the process. Take R = 0.287 kJ/kg-K and Cv = 0.713 kJ/kg-K.
2. A piston-cylinder assembly with stops (see figure) contains 1.54 kg of water initially occupying a volume of 1.25 m at a pressure of 1 bar (State 1). As the water in the assembly is heated, the pressure and temperature in the system remain constant until the piston contacts the stops. In this position (State 2), the quality, x2, is determined to be 92%. Heat continues to be added to the system at a constant volume until the system reaches a pressure of 1.5 bar (State 3). Determine the following quantities: а. X b. V2 (m2) C. W13 (kJ) d. Qu (kJ) e. Plot the results on a P-v diagram, labelling relevant P, T, and v values.
Question 2 The work done during polytropic expansion of gas from state 1 to state 2 is given by: W = (P₂V₂ - P₁V₁) 1-n A pressurised reservoir connected to a vertical barrel is used to launch projectiles as shown in Figure Q2.1. Assume no leakage around the projectile, no friction and no pressure drop across the valve. The barrel is cylindrical with a diameter, D = 50mm and a length, L = 0.8m. The mass of the projectile, M = 1kg. The volume of the reservoir, V = 2 litres. Atmospheric pressure is 1.01 bar. 0 L M Barrel Valve Figure Q2.1 Reservoir Volume, Vr a) By applying conservation of energy, for an initial reservoir pressure and temperature of 2bar and 20degC and assuming polytropic expansion with n = 1.3, find the exit velocity of the projectile. b) If the valve shuts at the instant the projectile leaves the barrel, what mass of gas is used to launch the projectile? c) Prove that a barrel length of 0.64m results in maximum exit velocity. d) Using this barrel length, what is the…
A closed, rigid, 0.5 m³ tank is filled with 6.0 kg of water. The initial pressure is p₁ P2 = 4 bar. Determine the initial quality, x₁, and the heat transfer, in kJ. = 20 bar. The water is cooled until the pressure is
Saturated steam at P1=25 bar expands adiabatically through a throttling valve to P2=4 bar. If the quality of the steam at the valve inlet is x1=0.9 what is the quality x2 at the valve outlet Please respond ASAP
I need the answer as soon as possible
Please show the complete solution.