As shown in the figure, air with a volumetric flow rate of 17,000 ft/min enters an air-handling unit at 80°F, 1 atm. The air-handlingunit delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. Thevelocity in each 26-in. duct is 19 ft/s. Assume steady state operation and ideal gas behavior for the air.4+D - 50 in.DuctsystemT2 = 73 = T, = 45°FD; = Dz = 26 in.V2 = V3Air-handling unit1+ Pi = P2 = P3 = P4 = 1 atmT = B0°F(AV),Determine the mass flow rate of air entering the air-handling unit, in Ib/s, the volumetric flow rate in each 26-in. duct, in ft/min, andthe velocity in the 50-in. duct, in ft/s.

Answered: Image /qna-images/answer/ef9f9888-bab6-4671-b368-546221ca48ee.jpg

Answered: As shown in the figure, air with a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

| Part of a refrigeration system operates at steady state with Refrigerant 22 as shown in the figure below. There is no significant heat transfer to or from the heat exchanger, valve, and piping. Kinetic and potential energy effects are negligible. State 1 is a saturated liquid. What temperature is it, in °F? Describe the refrigerant at state 4 as one of the following: compressed liquid, saturated liquid, tyro-phase mixture, saturated vapor, or superheated vapor. Determine the required mass flow for the given operating conditions, in lb/min. Determine the rate of heat transfer between the evaporator and its surroundings, in b. Btu/min. Make sure to clearly state the direction of heat transfer. 1. T=10°F P= 15 Ibf in (AV), = 9.5 ft/min. Pi= 120 Ibf/in.? Heat exchanger Throttling valve Evaporator P 15 lbfin.2 X3 = 1.0 P2= 15 lbf/in.2
Instructions: Write the complete solution with cancellation of units. PROBLEM |. In a constant volume process, 1.5 kg of air is cooled from 1,200 °K. Change in entropy is - 0.492 KJ Determine the final temperature in °K. K
Consider the extraction of energy from the tail gases from a nitric acid adsorption tower, such as that described in Chapter 4, Example 4.4. Gas composition, kmol/h: 0₂ N₂ NO NO₂ H₂O 371.5 10,014.7 21.9 Trace saturated at 250°C If the gases leave the tower at 6 atm, 25°C, and are expanded to, say, 1.5 atm, calculate the turbine exit gas temperatures without preheat, and if the gases are preheated to 400°C with the reactor off-gas. Also, estimate the power recovered from the preheated gases.
As shown in the figure, air with a volumetric flow rate of 16,000 ft/min enters an air-handling unit at 80°F, 1 atm. The air-handling unit delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. The velocity in each 26-in. duct is 16 ft/s. Assume steady state operation and ideal gas behavior for the air. 4+ Da = 50 in. Duct T2 = 73 = 1= 45°F D, - D,- 26 in. V2 = V3 system Air-handling unit 1- = P2 = P3 = p4 = 1 atm T = B0°F (AV), Determine the mass flow rate of air entering the air-handling unit, in Ib/s, the volumetric flow rate in each 26-in. duct, in ft/min, and the velocity in the 50-in. duct, in ft/s.
The density of a fluid decreases as it passes through a pipe of constant diameter. The mass flow rate of the outlet stream is ____________ the mass flow rate of the inlet stream. a. less than b. equal to c. greater than
A supply line carries a two-phase liquid–vapour mixture of steam at 450 psi. A small fraction of the flow in the line is diverted through a throttling calorimeter and exhausted to the atmosphere at 20 psi. The temperature of the exhaust steam is measured as 350°F. Determine the quality of the steam in the supply line. Select one: a. 95.7% b. 98% c. 92% d. 100%
17:06 O E 0 • 體三 сТ2(1).pdf Q 88 T CTQ2 Assuming the clearance is negligible for a single stage compressor with the following data. Atmospheric pressure: 90 kPa Atmospheric temperature: 17 C Delivery pressure: 7 bar Free air delivery flow rate: 0.2 m/min Take "n" as 1.3, Cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K Answer the questions for ethuto test With reference to files CTQ2 for question: Using file 2, which formula number will be used to evaluate the delivery temperature for an isentropic complession process? III
Determine the velocity in the 50-In. duct, In ft/s. V₂ - i ft/s
Step by step solution for mass flow, volumetric flow, and velocity please thank youu
Question C . Options A. Subsonic Nozzle B. Expansion Tube C. Diffuser D. Supersonic Nozzle
The figure shows data for a portion of the ducting in a ventilation system operating at steady state. The ducts are well insulated and the pressure is very nearly 1 atm throughout. The volumetric flow rate entering at state 2 is AV₂ = 3600 ft3/min. Assume the ideal gas model for air with cp = 0.24 Btu/lb-ºR and ignore kinetic and potential energy effects. (AV)₁ = 5000 ft³/min Air, Cp=0.24 Btu/lb R T₁ = 80°F p=1 atm 2 (AV)₂ T₂ = 40°F ft³/min 3 V3 = 400 ft/min T3 = ? -Insulation Determine the temperature of the air at the exit, in °F, and the rate of entropy production within the ducts, in Btu/min.°R.
Steam enters a control yolume that has one inlet and two exits. At the inlet (location 1) with a diámeterof 5.2 cm, the Steam has 100 bar , 360°C , and as mass flow rate of a Rg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the otner exit (locatión 3). For steady state opeaton, calculake the mass flow rate at locatlon 3 in kg/sec using 5 Signifigant figiures. रप्री द

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS