As shown in the figure, air with a volumetric flow rate of 14,000 ft3/min enters an air-handling unit at 80°F, 1 atm. The air-handling unit delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. The velocity in each 26-in. duct is 16 ft/s. Assume steady state operation and ideal gas behavior for the air. T₂ = 73 = T₁=45°F D₂=D₂ = 26 in. V₂=V3 A 4+D₁-50 in. Duct system Air-handling unit 1- P₁ = P₂ = P₁ = P4 = 1 atm T₁ = 80°F (AV)₁ Determine the mass flow rate of air entering the air-handling unit, in lb/s, the volumetric flow rate in each 26-in. duct, in ft3/min, and the velocity in the 50-in. duct, in ft/s.

As shown in the figure, air with a volumetric flow rate of 14,000 ft3/min enters an air-handling unit at 80°F, 1 atm. The air-handling unit delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. The velocity in each 26-in. duct is 16 ft/s. Assume steady state operation and ideal gas behavior for the air. T₂ = 73 = T₁=45°F D₂=D₂ = 26 in. V₂=V3 A 4+D₁-50 in. Duct system Air-handling unit 1- P₁ = P₂ = P₁ = P4 = 1 atm T₁ = 80°F (AV)₁ Determine the mass flow rate of air entering the air-handling unit, in lb/s, the volumetric flow rate in each 26-in. duct, in ft3/min, and the velocity in the 50-in. duct, in ft/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Course: Statics For Mechanical Engineers Chapter: Ch2 ( Force Vectors )
1.2) Problem. 3 The following forces (all pull) act at a point : (i) 25 N due North ; (ii) 10 N North-East ; (iii) 15 N due East ; (iv) 20 N 30° East of South ; (v) 30 N 60° South of West. Find the resultant force. What angle does it make with East ?
Q:Resolve the 170 Ib force of figure below into two components, one along AB and the other parallel to CD 3 A. 4 8. 15 12 170 5
D) Determine the true magnitude and direction of the forces acting on the cylinder
A cable is connected to an L shaped arm OAB as shown. The magnitude off the tensile force on the cable is given as T = 2500 and angle between the segment AB of the L- shaped arm and cable = 91.229 degrees. ( use the vector approach ) A) determine the components of the tensile force on the cable which are parallel and perpendicular to segment AB of the L-shaped arm
2-95 Four forces are applied at a point in a body as shown in Fig. P2-95. Determine the magnitude and direction (an- gles 6, By, and 6,) of the resultant R of the four forces. F= 300 Ib 30 F3= 150 Ib 60 3 ft F2 = 250 Ib F = 200 lb
I need the answer as soon as possible
Determine the angle, in degrees, between A and B if the component of A on B is -3.45 ax + 7.95 ay + 5.03 az and the component of B on A is 5.12 ax + -1.24 ay + 5.90 az.
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
Determine the magnitude of the force exerted by the cable at B of the bar shown in Figure. 260 3.5 m 2300 N 2.8 m 3.3 m
2.) Calculate the resultant force. (10PTS.) A = 2000lb D = 500lb 45° B = 1000lb 30° C = 2000lb