Steam enters a control yolume that has one inlet and two exis. At the inlet (location 1) with a diameter of 5.2 cm, the Steam has 100 bar, 360°C , and a mass flow rate of 2 kg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the other exit locatión 3). For Steady state operaton, calculake . Dthe mass flow rate at lo cation 3 in kg/sec using 5 signifigan figures... है

Steam enters a control yolume that has one inlet and two exis. At the inlet (location 1) with a diameter of 5.2 cm, the Steam has 100 bar, 360°C , and a mass flow rate of 2 kg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the other exit locatión 3). For Steady state operaton, calculake . Dthe mass flow rate at lo cation 3 in kg/sec using 5 signifigan figures... है

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Describe the T-s diagrams accordingly by filling in the blanks. Use the sets of words given below for the correct description. reheat/ closed Ideal / Actual / vapour /cycle /Carnot/ Rankine/ Brayton/Ericsson/Stirling/regenerative/ open/with/a Nino To C @ 4 2. 5. 6. a b с e T f 1 4 In a two-stage gas turbine plant, with reheating after the first stage TA 25 decreases the thermal efficiencies. increases the thermal efficiencies. does not affect thermal efficiencies. Decreases the work ratio. increases the work ratio. does not affect the work ratio. equal. unequal. 2 5 The ideal compressor work and turbine work in a jet-propulsion engine is a b 9in 2/ qout Wpump.in High-pressure turbine 3 Reheating 6 Wturb,out Low-pressure turbine с not related to each other. d unpredictable (a) By writing an energy balance on the heat exchanger of a binary vapour power cycle, obtain a relation for the exit enthalpy regarding the mass flow rates of two fluids in terms of the other enthalpies. Take the…
Write please In copy
6. A four-stroke, 6-cylinder, 3.6 Itr SI engine, is designed to have a maximum speed of 6000 r.p.m. At this speed, the volumetric efficiency of the engine is 0.92, fuel density is 700 kg/m C 15. Calculate: (1) %3! 0.85, C 0.6, Apg = 0.07 bar, at sea level T, = 27°C, p. = 1.03 bar, and AE Throat diameter of the carburetor. (2) Fuel orifice area. (3) AF at altitude of 4000 m
Show the correct and complete solution to this problem. ASAP. Thanks!
4.1 A gas turbine power plant is operating as follows. Compressor intake air temperature T, is 306 K, pressure p, is 100 kPa, and compressor pressure ratio B is 15. TIT T, is 1490 K. Isentropic efficiency of compressor N, is 0.88, and that of turbine n is 0.91. Air mass flow rate mi, is 636 kg/s. Fuel mass may be ignored. Calculate (i) actual temperatures at compressor and turbine exits, (ii) plant actual net specific work per kg air, (iii) plant actual power output, (iv) plant actual rates of heat addition and rejection, and (v) plant actual thermal efficiency.
34 - Helium enters a continuous flow compressor at 326 K and leaves at 441 K. If the mass flow rate is 1.5 kg/s, which of the following is the required power? (Cp = 5.1926 kJ/kgK) a) 988.7 kW B) 895.7 kW NS) 617.9 kW D) 927.9 kW TO) 836.0 kW
What is the enthalpy of steam at 155 deg C? Find the specific enthalpy of superheated steam at 2 atm and 900°C.
Anideal gas with a mass of 2 kg reversibly and polytropically expands up to 3 times its initial volume in a piston-cylinder assem bly. The temperature of the ideal gas drops from 300° Cto 60° C. (a) If the heat energy inputis 20 kJand the boundary work output is 100 kJ, the specificheats of the gas cv [kJ/ kgK] and find the cp [kJ/ kgK] values. (b) If the heat energy output is 20 kJand the boundary work output is 100 kJ, the specificheats of the gas cv [kJ/ kgK] (c) Find the value k, which is the ratio of specificheats. (d) If the heat energy input is 20 kJ, the boundary work output is 100 kJ and the entropy generation is 0.36 kJ/K, then the thermal energy Calculate the source tem perature as [° C].
subject(fluid mechanic 2) pls show me full steps with clear handwrting sir pls answer me within 30 min sir
Net work input q in cop
The last 3 parts B,D,E