As per IS 875 (Part 3) - 1987, the basic wind speed at 10 m height for New Delhi has been recommended as 47 m/sec. A chimney is to be constructed for sugar mill with the stack height of 30 metres above ground. The speed of the surface winds to be considered for the safe construction of this chimney is.

As per IS 875 (Part 3) - 1987, the basic wind speed at 10 m height for New Delhi has been recommended as 47 m/sec. A chimney is to be constructed for sugar mill with the stack height of 30 metres above ground. The speed of the surface winds to be considered for the safe construction of this chimney is.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.30. The performance of a centrifugal blower at its point of best effi- ciency is Q = 10 m3/s, Aps = 5kPa, and ns density is p N = 475 s-1. 0.875. The inlet air 1.21 kg/m and the size and speed are D = 0.7 m and | a. At what speed would this blower generate 1 kPa at BEP? b. What will the BEP flow rate be at this speed? c. Calculate the required shaft power at the speed found in (a).
A 4.0 MW fire burns at 1 m above the floor in a large warehouse with a 5.0 m flat ceiling height. What are the ceiling jet temperatures and velocities i. directly above the fire ii. at a radial distance of 2.0 m?
Draught produced by stack 30 meters high for maximum rate of discharge of hot gases through it at 27°C is (a) 17.65 mm H₂O (b) 35.5 mm H₂O (c) 30 mm H₂O (d) Not possible to find with the data
Calculate the required fire flow and duration for a fire-resistive apartment building that has four floors, each with 4200m². The vertical openings are protected, and the entire building is equipped with automatic sprinklers. The neighborhood where this building is located has a large number of houses with wood shake roofs. Consider a side separation of 6m, and ignore the front and rear separation.
(a) (Choose only one of the options below) If the current statistical data is not available, the wind generated current velocities (U) at the SWL may be computed from the 1 hr mean wind speed (Uw) at a 10 m elevation as, U = (i) (ii) (iii) (iv) 0.051UW 0.150UW 0.015UW 0.0015UW (b) (Choose only one of the options below) Per API RP 2A design guidelines, what is the duration of the wind gust to be used to calculate design wind speed for a component on the topsides of a platform whose maximum horizontal dimension is more than 164 ft (i) (ii) (iii) (iv) 3 seconds 5 seconds 15 seconds 20 seconds (c) (Choose only one of the options below) Per API RP 2A design guidelines, for the global environmental load analysis of a steel jacket structure, the recommended value of drag coefficient Ca to be used in Morison's equation for a hydro dynamically rough unshielded and slender tubular member is (i) 1.05 (ii) 1.50 (iii) 1.75
A petroleum refinery emits 80 g/sec of SO, from an effective height of 60 m (physical stack height 45 m) in an area with flat terrain. At 8 a.m. on an overcast winter morning when the surface wind (measured at a height of 10 m) is 6 m/sec, what is the ground-level concentration directly downwind from the refinery at a distance of 500 m? What is the concentration at the same distance downwind but at a distance 50 m crosswind from the centerline?
The unheated storage facility is located on flat open terrain near Sicilia Island, Italy. Determine the design snow load on the roof. How about if the slope of the roof is 45° ?
Water from a reservoir is pumped to a higher elevation through a 450mmφ and a pressure of 250 kPa is maintained at the summit where the pipe is 110 m above the reservoir. The pipe discharges 1.56 m3/s and total losses due to friction is 8 m. What output power must be furnished to the water?
Complete answer
P2.15) Determine the dead load and live load for the second floor of a library in which any area can be used for stacks. Assume that there will be a steel channel ceiling system (2 psf) and asphalt tile on the floors. The floors are 6-in. reinforced concrete. Allowance should be provided for mechanical ducts.
which pitch?