2.30. The performance of a centrifugal blower at its point of best effi-ciency is Q = 10 m3/s, Aps = 5kPa, and nsdensity is pN = 475 s-1.0.875. The inlet air1.21 kg/m and the size and speed are D = 0.7 m and|a. At what speed would this blower generate 1 kPa at BEP?b. What will the BEP flow rate be at this speed?c. Calculate the required shaft power at the speed found in (a).

a. Speed: V = 2DP/ρ V = (2 X 0.7x0.0101972/1.21) V = 0.112 m/s FOR 1 KPa

The performance of a centrifugal blower at its point of b ciency is Q = 10 m³/s, Aps = 5 kPa, and ns = density is p = 1.21 kg/m³ and the size and speed are D = N = 475 s-1. 0.875. The i %3D 0.2 %3D a. At what speed would this blower generate 1 kPa at BEP? b. What will the BEP flow rate be at this speed?

The performance of a centrifugal blower at its point of b ciency is Q = 10 m³/s, Aps = 5 kPa, and ns = density is p = 1.21 kg/m³ and the size and speed are D = N = 475 s-1. 0.875. The i %3D 0.2 %3D a. At what speed would this blower generate 1 kPa at BEP? b. What will the BEP flow rate be at this speed?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a laminar flow through a channel, Reynold's number is given by 1500, what is the friction factor?
Two pipes A and B are connected in parallel between two points. Pipe A is 200 m long and has a diameter of 16 cm, pipe B is 150 m long and has a diameter of 12 cm. Both the pipes have the same friction factor of 0.018. A partially closed valve in pipe 'A' causes the discharge in the two pipes to be the same. All other minor losses can be neglected. The value of the valve coefficient is - Valve F = 0.018 L=200m, d-16cm L,=150m, d=12cm B F = 0.018
92 Calaulate the flow rate of the each pipe is given belowi O.120m/s (4) K2=2 (2) Ku=4 (3) (5) Es=5 0.040 m/s O-030 ms The initial value of the flow rate for pipes ore gren as Ri=0.07 /s 92=0.05 m/s 93= 0.01 m% Q4=0,01ms and Q5=0,03 m3
23. The ratio of the momentum correction factor to the energy correction factor for a laminar flow in a pipe is (a) m/a alm (c) 23/ (b) 1 (d) 2
Correct solution.
Determine the kinetic energy correction coefficient for the compound channel shown in Figure 2.1 below. Im V,=0.5m/s V,=0.3m/s 20m 22m 3m Figure 2.1 4m V,=1.5m/s
Q-A pelton wheel works under a head of 400m. Friction loss through the pipe flow is limited to 10%. The coefficient of velocity for the jet is 0.98. What is the velocity of the jet? Take g = 10 m/s².
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az