Arsenic (III) sulfide is reacted with oxygen gas to form arsenic (III) oxide and sulfur dioxide. Calculate the amount of arsenic (III) sulfide needed to produce 738.22 mL of sulfur dioxide at STP. Atomic Mass: Ar: 74.922 g/mol S: 32.065 g/mol O: 15.999 g/mol Round your answer to 2 decimal places. Add your answer

Arsenic (III) sulfide is reacted with oxygen gas to form arsenic (III) oxide and sulfur dioxide. Calculate the amount of arsenic (III) sulfide needed to produce 738.22 mL of sulfur dioxide at STP. Atomic Mass: Ar: 74.922 g/mol S: 32.065 g/mol O: 15.999 g/mol Round your answer to 2 decimal places. Add your answer

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

(Handwritten answer) Calculate range of volumes representing 0.1% tolerance of a 25.00 mL volumetric pipette assuming that 25.00 mL is the dispensed volume!
If a water sample has 0.07 mol of calcium ions in 15 L solution, what is the water hardness level in mg/L? Pay attention to the unit. Hint: For the calcium mass , convert mol to g to mg. (1 mol calcium ion= 40.08 g/mol and 1 g = 1000 mg) Round and report your answer to an integer without decimal place. Report numeric value only, no unit. • Water hardness levels according to EPA Soft: 0-60 milligrams per liter (mg/L) as calcium carbonate Moderately hard: 61-120 mg/L as calcium carbonate • Hard: 121-180 mg/L as calcium carbonate Very hard: more than 180 mg/L as calcium carbonate
MULTIPLE CHOICE: Choose the letter of the best answer Please answer all questions correctly 1. The standardization of volumetric solution does not require hydrochloric acid. A. Permanganometry B. Cerimetry C. Iodimetry D. lodometry E.All of the choices 2. In the standardization of its volumetric solution, the primary standard is dried to constant weight, which means drying shall be continued until two consecutive weighings do not differ by more than 0.50 mg. A. Permanganometry B. Cerimetry C. Iodimetry D. lodometry E.All of the choices 3. In the standardization of its volumetric solution, potassium iodide was added to A. Permanganometry B. Cerimetry C. Iodimetry D. lodometry E.All of the choices 4. Starch is the indicator of choice for these procedures because it forms intense blue coloration with the solution. A. Permanganometry B. Cerimetry C. Iodimetry D. lodometry E. C and D 5. In the standardization of its volumetric solution, the reaction needs to be…
What is the mass percent of HCIO3 in a solution made of 38.57 g of HCI03 dissolved in 398 g of water? Please express your answer to the first decimal place. Type your answer..
I need help calculating the moles of acid and basebised and also the molarity of the base solution oles RECORD ALL DATA IN INK using the correct number of significant figures and correct units. SHOW COMPLETE "SET-UPS" (and the rounding off) for all calculations for Part 3 on the bottom of this page or on a separate sheet. 3. Standardization of the NaOH Solution: Titration No. Acid buret, Final reading Initial reading Volume of acid used Moles of acid used Base buret, Final reading Initial reading Volume of base used Moles of base used Molarity of base solution Set-ups: 1 2 3 24ml 36. 24ml 12- 12 m 12ml Average Molarity of the NaOH solution Average Deviation 13 25.5 13 13 12.5ml 12 mil. 31.5 4 5 6
For the Shaefer-Fulton endospore stain method, the working solution of safranin is made by combining 10 mL of stock solution with 90 mL of distilled water. If you need to produce 1,046 mL of working solution, how many grams of safranin O will be required to make the smallest batch of stock solution possible? • Report your answer in grams using standard decimal notation rounded to two decimal places. • Include trailing zeros. • Do not include the units in your answer 。 If your answer is 100.105 g it would be reported as 100.11 。 If your answers was 100.203 g it would be reported as 100.20
You have run analysis on an unknown acetaminophen sample. Your results showed the concentration of acetaminophen in the unknown was 35.9%. The actual concentration of acetaminophen in the unknown was 49.0%. What is the error % for this analysis? Answer to 1 decimal place.
Using the following mass standard data, calculate the Rx value. mass of mass of area of area of isopentyl acetate (g) isopentyl alcohol (g) isopentyl acetate peak isopentyl alcohol peak 80.0 1.10 1.28 189 Please report your answer to 3 decimal places. (No units required)
Anna Divi, a young and ambitious researcher, is planning to put up her very own research laboratory. However, she does not have the funds for this to happen. She then approached Alan Read, CEO of a well-known funding agency, to help her pursue her dream laboratory. Before Alan considers Anna's proposal, Anna must perform an experiment on determining the melting point of solutions. She nust have an accurate result with a percent error not greater than 3%. The data on the experiment is given below. Help Anna achieve her goals by performing the necessary calculations below. Table 1. Data on the determnination of the melting point of the solution. Parameters Values Theoretical freezing point of solvent, °C 65.8 Freezing point depression constant (k 2.49 of solvent, °C m1 mass of solute, g 0.250 mass of solvent, g 2.100 molar mass of solute, g mol1 148.21
Mass of NaCl- 2.0139g
When performing the water displacement method , this observation will increase the volume of the specimen a. bubbles are produced b. the specimen floats c. mass was not accurately taken
Sample Method A Si wt% Method B Si wt% 1 11.570 11.510 15.380 15.350 17.950 17.900 4. 22.840 22.820 5. 25.110 25.190 6. 27.070 27.030 Determine faale- cale =