Arigid Cylinder containing 0.006m of nitrogen at 1.04 bar, 15c, is heated reversibly until the temperature is 90 c- Calculate the change of the process on Dexfect gas. entropy and the heat supplied.Sketch 7-sdiagram. Take 8=1-4,assume, nitrogen is a Ans.[ o.0o125 IGT, 0:407kg] k

Q: solution incorrect resolve again

A:

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: how does F_BC equal 6

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: Determine Stres

A:

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: D raio s.f.D and B.M.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: continue the question

A: Given: (d) The dimension of the plate: →A=1.2m*1.2m Because the distance of the center of gravity of…

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: If a = 9 in., locate the distance to the centroid of the member's cross-sectional area. (Figure 1)…

A: Draw the given diagram.

Q: Findss 30 kN-m

A:

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Q: M, B

A: Given data, The reaction at A and B can be calculated as -

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.