Answer ALL parts (8) Consider the circuit in Figure A4. (a) Explain its operation with the aid of diagrams. (b) Assume that R₁ = 21 k0, Vref= 1.2 V, V₁ = +12 V and -V, = -12 V. Determine a value for R₂ to obtain a maximum threshold voltage of Vth = 5.25 V. (c) Sketch the output voltage signal in time for a sinusoidal input signal of peak voltage 3.5 V and frequency 2 kHz. R1 R2 F Vref Hilt +Va

Answer ALL parts (8) Consider the circuit in Figure A4. (a) Explain its operation with the aid of diagrams. (b) Assume that R₁ = 21 k0, Vref= 1.2 V, V₁ = +12 V and -V, = -12 V. Determine a value for R₂ to obtain a maximum threshold voltage of Vth = 5.25 V. (c) Sketch the output voltage signal in time for a sinusoidal input signal of peak voltage 3.5 V and frequency 2 kHz. R1 R2 F Vref Hilt +Va

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A boost converter has an input voltage Vb-5V. The average load current is lo-0SA. The switching frequency is 25 kHz. Suppose that a regulator is added (L=0.15 mH and C-0.22 mF) and that the current is continuous. if the average output voltage is Vo =15V, then the ripple current of the inductor delta) is equal to: Select one: O a. None of these O b.0.89A O C. 1.41A O d. 0.56A
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 24 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +12 to -12 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is -6.0 volts, the delay angle (in degrees) would be: O A. None of the other choices are correct O B. 150 O C. -120 O D. 120 O E. 60
TRUE/FALSE QUIZ Answers can be found at www.pearsonhighered.com/floyd. 1. An ideal op-amp has an infinite input impedance. 2. An ideal op-amp has a very high output impedance. 3. The op-amp can operate in both the differential mode or the common mode. 4. Common-mode rejection means that a signal appearing on both inputs is effectively cancelled. 5. CMRR stands for common-mode rejection reference. 6. Slew rate determines how fast the output can change in response to a step input. 7. Negative feedback reduces the gain of an op-amp from its open-loop value. 8. Negative feedback reduces the bandwidth of an op-amp from its open-loop value. 9. A noninverting amplifier uses negative feedback. 10. The gain of a voltage-follower is very high. 11. Negative feedback affects the input and output impedances of an op-amp. 12. A compensated op-amp has a gain roll-off of -20 dB/decade above the critical frequency. 13. The gain-bandwidth product equals the unity-gain frequency. 14. If the feedback…
The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure Determine the data-output waveforms from D0 through D3.
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Design a buck converter such that the output voltage varies between from 20V to 28Vwhile the input voltage is 40V . The maximum load power is 200Wdc. Assume the switchingfrequency is 15kHz. (a) Design the converter such that it will be in continuous current mode.(b) The capacitor realized output voltage ripple must not be more than 1% at worst case.(c) The inductance realizes CCM at worst case.(d) Select the appropriate switch and other elements...
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.
A boost converter has an input voltage Vb=5V. The average load current is lo=0.5A. The switching frequency is 25 kHz. Suppose that a regulator is added (L=0.15 mH and C=0.22 mF) and that the current is continuous. If the average output voltage is Vo =15V, then the ripple current of the inductor delta() is equal to: Select one: a. 1.41A b. 0.56A O c. None of these d. 0.89A
i need the answer quickly
A step up DC converter is used to control power flow from a DC votage Vs=120V to a battery voltage E=200V. The power transferred to the battery is 10 kW. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: Oa. 0.5, 0.94 Ohms b. 0.4, 1.44 Ohms Oc. None of these O d. 04, 0.94 Ohms
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.