and dehumidifying through a cooling coil having apparatus dew point of 14°C and then by heating. Find: 1. The capacity of the cooling coil in tones of refrigeration and its by-pass factor; 2. The amount of water vapor removed by the cooling coil in kg/h and 3. The capacity of the heating coil in kW and its surface temperature, Assume the by-pass facto as 0 2

and dehumidifying through a cooling coil having apparatus dew point of 14°C and then by heating. Find: 1. The capacity of the cooling coil in tones of refrigeration and its by-pass factor; 2. The amount of water vapor removed by the cooling coil in kg/h and 3. The capacity of the heating coil in kW and its surface temperature, Assume the by-pass facto as 0 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Have to use thermodynamics concept
Need help solving this problem. Please provide clear and concise steps in neat handwriting.
200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at 5bar as saturated steam through a 5cm ID pipe neglect the change in potential energy of the system. What is the temperature of the outlet saturated system? How much energy is transferred to or from the turbine?
Elina is a businesswoman who is looking for a new invention to invest. One of the entrepreneur claimed to have a device which has 50 kJ of heat transfer at 500 K. The device having heat transfer of 250 K released to the environment and does 20 kJ of work. If you were Elina, would you willing to be one of the investor for the device?
What is the maximum theoretical COP for a freezer that is maintaining a temperature of -10 degrees celcius and exhausting heat to a kitchen that is 20 degrees celcius?
An insulated chamber containing 2 L of saturated liquid water at 300 kPa constant pressure. There is a piston-cylinder assembly. One with an electric heater inside the cylinder There is a mixer. Then the water is mixed by the mixer for a while. s mixed, as well as connected to 220 volt electrici supply and 8 A current through neated by the passing heater. This state change at constant pressure 500 kJ of work is done by the mixer. Meanwhile, iquid 90 percent by mass evaporates. a) Plot the state change on T-v and P-v diagrams, paying attention to saturation lines. D) Calculate the operating time of the electric heate
This question deals with a cylinder, which is upright. Here are the facts for the problem. Can you please help me with a clear diagram and then the right equations for net work and heat? There is a massless and frictionless piston inside the cylinder with two stops which prevent movement down the cylinder. But, the cylinder can still move upward. Under the Below the piston is 5 kg of water, 50% of which (by mass) is initially vapor at 120°C. Heat is gradually added to the water until the water reaches a final state of 400°C. The atmospheric pressure is 500 kPa. The stops don't affect the area. (1) Draw a P-V diagram for the process, which includes the isotherms at states 1 and 2. (2) A what temperature does the piston first lift off? At what temperature has the liquid turned to vapor? (3) What is the net work and heat transfer between the system and the surrondings between states 1 and 2. Are these transfers going into or out of the system?
A 4-kW heat pump is operated by a peasant. It should keep a duck hatchery at 32 degrees celsius, where heat is removed at a rate of 10 kW to the cooler ambient Tambient. What is the minimum COP for the pump that will be acceptable?
of Performance of the heat pump which should be higher than 100%) when the cabin temperature is 24°C and there is a 20°C temperature difference betveen the indoor cabin and outside at night?
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
could you explain were you get the numbers for formula to calculate heat transfer?Draw the T-V diagram showing all stages?Whats the final stage condition, is a gas, liquid explain? Solve using energy balance equation.
A spring-loaded piston-cylinder device contains of m=1kg carbon dioxide. Initially, the spring has no force on the piston and , , . Heat is transferred to the gas, causing the piston to rise and to compress the spring. At the state 2, , . The gas is an ideal gas. (7)How to calculate the total boundary work ?_____ A. B. C. D.