A Steam line at 0,7 MPa and 400°C is attached to a tank thatinitially Containsvalve Connechng the steam hne and tank is opened until thetank pressure becomes o.7 MPa, and then the valve is closed.Dunng the process, there is a heat transfer from the tank to theSurroundirigs at 300 °K, which amounts to 1000 kJ per eachKilogram of mass that the tank has at the end of the process.Calculate he final Specific entropy in the tank in kJlkg k)using 5 signifigant figires.verylittle water (assume zero initial mass). TheSteam LineTank

a line at 0,7 MPa and 40 IS attached tO a tank that Contains little water (assume zero initial mass). The Connecting the steam line and tank is opened until the ressure becomes 0.7 MPa, and then the valve is closed. the process, there is a heat transfer from the tank to the inigs at 300 °K, which amounts to 1000 kJ per each m of mass that the tank has at the end of the process. te he final Specific entropy in the tank in kJ/kg k) S signifigant figurs. very Steam Line Tank

a line at 0,7 MPa and 40 IS attached tO a tank that Contains little water (assume zero initial mass). The Connecting the steam line and tank is opened until the ressure becomes 0.7 MPa, and then the valve is closed. the process, there is a heat transfer from the tank to the inigs at 300 °K, which amounts to 1000 kJ per each m of mass that the tank has at the end of the process. te he final Specific entropy in the tank in kJ/kg k) S signifigant figurs. very Steam Line Tank

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An insulated chamber containing 2 L of saturated liquid water at 300 kPa constant pressure. There is a piston-cylinder assembly. One with an electric heater inside the cylinder There is a mixer. Then the water is mixed by the mixer for a while. s mixed, as well as connected to 220 volt electrici supply and 8 A current through neated by the passing heater. This state change at constant pressure 500 kJ of work is done by the mixer. Meanwhile, iquid 90 percent by mass evaporates. a) Plot the state change on T-v and P-v diagrams, paying attention to saturation lines. D) Calculate the operating time of the electric heate
The vacuum at the steam inlet to a condenser was found to be 716 mm of Hg and the temperature of steam in the condenser is 35 o C, when barometer reads 760 mm of Hg. Find the vacuum efficiency.
Q.3 Find the increase in unavailable energy associated with transfer of 800kJ of heat from a constant temperature system at 600K to another constant temperature at 400K. The ambient temperature is 300K. A 150kJ В 182kJ C 200kJ D 220kJ
I can't Figure out this? 1.83 Wrong.
H.W/ Steam at 10bar, 0.95dry is heated electrically at constant pressure process. If the rate of consume power is 1kW and the rate of steam is 0.3kg/min, determine the final state of steam?
In a frictionless piston-cylinder system, 5 kg of R-134a superheated steam at 1000 kPa and 140It is in ˚C. Fixed up to 25% dryness degree of system R134apressure cooled. Find the work done in the system. Show the process in the P-v diagram
A piston with water vapor at a pressure of 300 kPa and a temperature of 175 oC. 20 kg of fluid is compressed up to 950 kPa pressure in the cylinder arrangement. Piston cylinder device to a heat well at 80 oC in order to keep the temperature of the water in it constant. The heat generated during compression is discarded. a) What phase is the water in the first case? In the last case, what phase is the water in? b) Find the entropy change in water by the process. c) From the cylinder, assuming that the process is a reversible process at constant temperature. Calculate the amount of heat absorbed. d) Find the entropy change of the heat well. e) Consider the total entropy change including the piston-cylinder mechanism and the heat indicate whether the transaction is reversible or irreversible when received. f) T (° C) -s (kJ / kgK) and P (Pa) - by specifying the state change saturation curves and values Show in (m³ / kg) diagrams.