Answered: Analyze the given pin jointed frame (in…

Analyze the given pin jointed frame (in Figure 2) using stiffness method. EA is constant for all the members. 72in 84in 72 in 72 in Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar DB in the figure is supported at pin B by axial member ABC, which has a cross-sectional area of A1 = A2 = 85 mm², an elastic modulus of Ej = E2 = 1000 MPa, and lengths of L = 390 mm and L2 = 645 mm. Aload of Q = 555 N is applied at end Cof member (2), and a load of P = 1425 N is applied to the rigid bar at a distance of a = 85 mm from pin support D and b = 45 mm from pin B. Determine the magnitudes of the downward deflections of: (a) pin B. (b) pin C. A |(1) Rigid bar B a b. L2 (2) (a) VB = i mm (b) vc = i mm
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.250 in. thick, and made of aluminum that has an elastic modulus of E = 10,100 ksi. Assume that a = 16 in., b = 27 in., c = 11 in., and d = 20 in. Determine the maximum magnitude of load P that can be applied to the rigid bar without causing member (1) to buckle.
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 120 in. Rod (1) has a length of L1 = 87 in. and a cross-sectional area of A1 = 0.65 in.2. Rod (2) has a length of L2 = 84 in. and a cross-sectional area of A2 = 1.15 in.2. Rigid bar ABC is to remain horizontal under a load of P = 25 kips. Determine the distance x (in inches rounded to the nearest tenths) from joint A to the location of load P so that bar ABC remains horizontal.
A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
Cho lmao
The steel framework is used to support the reinforced stone concrete slab that is used for an office. The slab is 200 mm thick. Sketch the loading that acts along members BE and FED. Take a = 3 m, b = 4 m. Hint: See Tables 1.2 and 1.4.
The truss ABC is constructed of three titanium (E Ti =17.4×10 3 ksi) members. A horizontal force of 1.8 kip and an unknown force P are applied to the truss at point B as shown. Member AB has a cross-sectional area of 0.1in 2 , member BC has a cross-sectional area of 0.0025ft 2 , and member AC has a cross-sectional area of 0.2 in2. b) Determine the magnitude of the force P that is required to displace the roller at point C to the right by .03 inches.
For the steel truss (E=29 × 106 psi) and loading shown, determine the deformations of members AB and AD, knowing that their cross- sectional areas are 4.0 in2 and 2.8 in2, respectively. It is given that P= 50 kips. P A B 8 ft D C -13 ft- -13 ft- The deformation of member AB is - in. The deformation of member AD is in.
Calculate all the member forces in the given truss using method of consistent deformation. Joint D is pinned supported and joint E is roller supported. F=4450 kN and L=8m. Take 'EA' same for all members В F 1 2 L 3 5 4 E
For a plane truss member, the length is 2 m, E = 200 GPa and area of cross-section is 200 mm². The stiffness matrix coefficient K₁1 with reference to its local axis is A) 200 N/m B 2 × 107 N/m C) 4 x 107 N/m с D) 400 N/m
The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m². The cross sectional area of each member is 0.01 m?. Forces P, and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 3 409 (c) 30 P1 P= 2kN 4m FIGURE Q2 а. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by performing complete calculations to justify your recommendation.
The length of a plane truss member is 2.5m. What will be the stiffness matrix coefficient k₁1 for this truss? Consider E= 210 GPa and area of cross section is 150 mm².