Analyze the cable shown below to determine the forces P1 and P2 needed to hold the cable in the position shown i.e., so that segment CD remains horizontal. Also find the maximum loadng in the cable.

Q: -9 m 6 m- A 12.25 m a C B 60 kg/m

A:

Q: Cable ABCD supports the loading shown.Determine the tension in member BC,angle B1 and angle B2 6m…

A:

Q: A 600 N B 400 N C E D 150 mm 100 mm-150 mm- 80 mm 100 mm

A: Beam ABCD supported by cables BE and CF

Q: Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the…

A:

Q: 0.8 Figure below is of force polygon of a loaded suspend cable. op, oq, or and os represent the…

A: Given, Force polygon of suspended cable. We need to find the value of T1.

Q: Cable ABCDE supports the loading shown. Determine the tension in member DE, the value of Yd and the…

A: Determine the tension in member DE, the value of Yd and the value of Yb

Q: 1.1.8, T is wrong, please correct.

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: As shown below, the cable AE supports three vertical loads from the points indicated. Determine the…

A: The cable is the flexible member which mainly resist the tension force and not the compression…

Q: Given: The structure shown below is cantilevered at the Point A and welded at point B.  In addition,…

A:

Q: Figure 2-83 7. Determine the maximum sag and the largest tension in 4k 24 1 4k the 30 ft 30 ft 30 ft…

A:

Q: Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910…

A:

Q: Calculate the tension in the cable, and the reactions at A and C 100 mm 100 mm 300 mm 400 N C 400 N…

A:

Q: Determine the tension in each cable and the components of reaction at D

A:

Q: A rigid bar ABCD is pinned at end A and supported by two cables at points B and C (see figure). The…

A:

Q: 30° A B 800 16 30 in 30 in 30 in

A: Given Data:  Angle between rope and beam = 30o Load acting on beam = 800 lb Let tension in rope be T…

Q: 4-3* Two ¹/4 -in.-diameter steel cables A and B are used to support a 220-lb traffic light as shown…

A:

Q: The ball D has a mass of 20 kg. If a force of F = 100 Nis applied horizontally to the ring at A,…

A: First, we draw the free body diagram:-

Q: Q1: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of…

A: Given: A cable supporting 3 downward forces. Find: Resultant of these forces and its location w.r.t.…

Q: The cable carrying three 400-lb loads has a sag at ate the force in each segment of the cable. - 8…

A: Draw free body diagram Consider the summation of forces in the horizontal direction Ax=Ex…

Q: -3 m- В C www 2 m イ D A The assembly above is comprised of cables and a spring (k = 1000 N/m). The…

A:

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A: Reference : Engineering Mechanics, Tension in cable. Given : Mass = 25 tons = 25000 kg A force P…

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: The sign shown has a mass of m = 121 kg and is supported by two cables and a ball and socket at A.…

A: The  mass of the signboard, m = 121 kgThe board is supported by two cables at points E and B.To…

Q: Problem 4) Assume the loads applied to the beam result in a uniformly horizontally distributed load…

A: A loaded beam is given in the as shown and it has been asked to determine intensity of uniformly…

Q: Consider the structure shown below. Determine the tension in the cable and the horizontal and…

A: Given: Weight of cylinder = 80lb

Q: For the beam and loading shown, determine the tension in the cable at D and the support reactions at…

A:

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A: TAB=8.1KN To find tension in cable AC and resultant R

Q: The 1635-lb uniform plate ABCD can rotate freely about the hinge AB. The plate is supported by the…

A: The weight of the plate will be concentrated at the centroid. Since the plate is symmetrical, the…

Q: 4 ft 8 ft y 7.5 ft 6 ft Question 8 x 6 ft What is the x-component of the reaction force at A (in lb)…

A:

Q: Ex. Calculate tension in each segment of cable and vertical sag at B. hs B 3kN 8kN 2m

A: Given :

Q: Problem (4) The rod AB is suspended from two rigid cables. When the rod is hanging in th position…

A: total weight of rod acting at C.G    W=6.8+5.2=12 lbweight at A   wA=6.8 lb and wt at B  wB=5.2…

Q: A 30° 2 m 2 m C 2 m

A:

Q: The cable is subjected to a uniform loading as shown. If the slope of the cable at point 0 is zero,…

A:

Q: 4. Determine tho B1. B2. B3 &B4, forces in each segment and the total length of the cable. I y=15m…

A:

Q: The cable AB carries a uniformly varying load. It is connected to a wall at A and is held in…

A:

Q: Member ABF is held in place by a ball-and-socket support at A and by wires GB, HD, and JF as shown.…

A:

Q: A cable supports two vertical loads as shown in Fig. If the maximum tension in the cable is 2000 lb,…

A: Draw free body diagram Consider the moment equilibrium about point A…

Q: 5. Cables A, B and C support a 50 lb load as shown. Determine; a) The magnitude of the tensions in…

A: Determine; a) The magnitude of the tensions in each cable b) Express the tension in each cable in…

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.